Publicité
Liens rapides
DECLARATION OF CONFORMITY
This product is marked
– Low voltage no. 73/23 EEC and 93/68 EEC.
– Electromagnetic compatibility no. 89/336 ECC, 92/31 EEC and 93/68 EEC.
This declaration will become void in case of misuse and/or non observance though partial of manufacturer's installation and/or
operating instructions.
OPERATING LIMITS
í Cooling Maximum conditions
Outdoor temperature : 46°C D.B.
Room temperature
: 32°C D.B. / 23°C W.B.
í Cooling Minimum conditions
Outdoor temperature : 19°C D.B.
Room temperature
: 19°C D.B. / 14°C W.B.
í Heating Maximum conditions
Outdoor temperature : 24°C D.B. / 18°C W.B.
Room temperature
: 27°C D.B.
í Heating Minimum conditions
Outdoor temperature : –8°C D.B. / –9°C W.B.
ACCESSORIES SUPPLIED WITH THE UNIT
PARTS
FIGURE
Q.TY
4
SCREW M5 X 30
REMOTE
1
CONTROL UNIT
TWIN WIRE CABLE
1
**
Available only for heat pump models.
*
Available only for CAF94-124
**
as it satisfies Directives:
PARTS
FIGURE
Q.TY
FULL SCALE
1
DIAGRAM
DRAIN
1
ELBOW
*
MOUNTING PADS
4
37.4163.271.1
INSTALLATION INSTRUCTIONS
Model Combinations
Combine indoor and outdoor units only as listed below.
Indoor Units
CAF94R5TA-
CAF124R5TA-
CAF185R5TA-
Power Supply:
5: 220 - 240 V ~ 50 Hz / 7: 380-400 V - 3N ~ 50 Hz
Tools required for installation (not supplied)
1. Standard screwdriver
2. Phillips head screwdriver
3. Knife or wire stripper
4. Tape measure
5. Level
6. Sabre saw or key hole saw
7. Hacksaw
8. Core bits ø 5
01/2006
- Cassette split units -
Outdoor Units
GRF94C5TA-
GRF95L5TA-
GRF94R5TA-
GRF124C5TA-
GRF125L5TA-
GRF124R5TA-
GRF185C5TA-
GRF185C7TA-
GRF185L5TA-
GRF185L7TA-
GRF185R5TA-
GRF185R7TA-
19. Hammer
10. Drill
11. Tube cutter
12. Tube flaring tool
13. Torque wrench
14. Adjustable wrench
15. Reamer (for reburring)
16. Hex. key
EG
I
F
D
E
Publicité
Manuels Connexes pour Technibel CAF94R5TA Serie
Sommaire des Matières pour Technibel CAF94R5TA Serie
- Page 1 INSTALLATION INSTRUCTIONS - Cassette split units - DECLARATION OF CONFORMITY This product is marked as it satisfies Directives: – Low voltage no. 73/23 EEC and 93/68 EEC. – Electromagnetic compatibility no. 89/336 ECC, 92/31 EEC and 93/68 EEC. This declaration will become void in case of misuse and/or non observance though partial of manufacturer's installation and/or operating instructions.
- Page 2 DIMENSIONS (mm) Suspension brackets Suspension brackets Ceiling Fresh air intake side SUSPENSION BRACKETS Suspension bolt Ceiling Electrical components box Nuts and washers Refrigerant tubing side REFRIGERANT TUBING SIDE Refrigerant tubing joint (NARROW tube) Refrigerant tubing joint (WIDE tube) Condensate drain piping NET WEIGHT CAF94/124 CAF185...
- Page 3 IMPORTANT! • Ground the unit following local electrical codes. Please read before installation • The Yellow/Green wire cannot be used for any connection different from the ground connection. • Connect all wiring tightly. Loose wiring may cause overheating This air conditioning system meets strict safety and operating at connection points and a possible fire hazard.
- Page 4 Installation site selection - Indoor unit can be uniformily cooled. AVOID • Select a sufficiently strong ceiling to support the weight of the unit. • Direct sunlight. • Select a location where tubing and drain hose have the shortest run •...
- Page 5 ISTRUZIONI DI INSTALLAZIONE - Condizionatori d’aria Split System cassette - DICHIARAZIONE DI CONFORMITÀ Questo prodotto è marcato in quanto conforme alle Direttive: – Bassa Tensione n. 73/23 CEE e 93/68 CEE. – Compatibilità Elettromagnetica n. 89/336 CEE, 92/31 CEE e 93/68 CEE. Questa dichiarazione sarà...
- Page 6 DIMENSIONI (mm) Staffe di sospensione Staffe di sospensione Soffitto Lato ripresa aria esterna STAFFE DI SOSPENSIONE Tirante di sospensione Soffitto Scatola componenti elettrici Dadi e rondelle Lato tubi refrigerante LATO TUBI REFRIGERANTE Attacco tubo refrigerante (tubo PICCOLO) Attacco tubo refrigerante (tubo GRANDE) Attacco scarico condensa PESO NETTO...
- Page 7 IMPORTANTE! • Eseguire la messa a terra dell’unità secondo le norme Leggere prima di iniziare l’installazione elettriche locali. • Il conduttore giallo/verde non può essere utilizzato per collegamenti diversi dalla messa a terra. Questo sistema di condizionamento deve seguire rigidi standard •...
- Page 8 Scelta del luogo di installazione unità interna essere uniformemente climatizzato. EVITARE • Verificare che il soffitto sia sufficientemente resistente da sostenere il peso • L’esposizione diretta al sole. dell’unità. • Scegliere una posizione in modo che la distanza tra le due unità sia la •...
- Page 9 NOTICE D’INSTALLATION NOTICE D’INSTALLATION - Climatiseurs split cassette - DECLARATION DE CONFORMITE Ce produit est marqué puisque il est conforme aux Directives: – Basse Tension n. 73/23 CEE et 93/68 CEE. – Compatibilité Electromagnétique n. 89/336 CEE, 92/31 CEE et 93/68 CEE. Cette déclaration sera nulle en cas d'une utilisation différente de celle déclarée par le Constructeur et/ou de la non-observation, même si partielle des instructions d'installation et/ou d’utilisation.
- Page 10 DIMENSIONS (mm) Brides de suspension Brides de suspension Plafond Côté reprise de l’air extérieure BRIDES DE SUSPENSION Tige de suspension Plafond Boîte des composants électriques Ecrous et rondelles Côté tubes frigorifique COTE TUBE FRIGORIFIQUE Raccord tube frigorifique (tube PETIT) Raccord tube frigorifique (tube GROSS) Raccord sortie des condensâtes POID NET...
- Page 11 IMPORTANT! • Effectuez la mise à la terre de l'appareil en respectant les Veuillez lire ce qui suit avant de commencer réglementations électriques locales. • Le câble jaune/vert ne peut en aucun cas être utilisé pour toute Ce système de conditionnement de l'air répond à des normes autre connexion que celle de la mise à...
- Page 12 Choix de l'emplacement d'installation - Appareil intérieur RECHERCHEZ • Un emplacement approprié à partir duquel l'ensemble de la pièce peut être EVITEZ climatisé de manière uniforme. • L'exposition directe au soleil. • Un plafond suffisamment solide pour supporter le poids de l'appareil. •...
- Page 13 INSTALLATIONSANLEITUNGEN - Kassetten Split-Wandgeräte - KONFORMITÄTSERKLÄRUNG Dieses Produkt ist mit -Zeichen gekennzeichnet, weil es den folgenden Richtlinien entspricht: – Niederspannungsrichtilinie 73/23 EWG und 93/68 EWG. – Elektromagnetische Verträglichkeit 89/336 EWG, 92/31 EWG und 93/68 EWG. Bei falschem Einsatz des Gerätes und/oder Nichtbeachtung auch nur von Teilen der Bedienungsanleitung und der Installatinsanweisungen wird diese Erklärung ungültig.
- Page 14 AUSMAßE (mm) Aufhängungs-Halterungen Aufhängungs-Halterungen Decke Lufteintritt von Außen AUFHÄNGUNGS-HALTERUNGEN Aufhängungs-Befestigung Decke Elektrische Dose Mutter und Scheiben Kühlrohren Seite KÜHLROHREN SEITE Kühlrohr Verbindung (ENGES Rohr) Kühlrohr Verbindung (WEITES Rohr) Kondenswasser-Auslaß-Verbindung NETTO GEWICHTE CAF94/124 CAF185 Modelle EINHEIT RAHMEN-GITTER-BAUGRUPPE...
- Page 15 WICHTIG! Verbindungen unzureichende Erdung können Bitte vor Arbeitsbeginn lesen Unfallverletzungen oder Tod verursachen. • Erden Sie das Gerät gemäß den örtlich zutreffenden Vorschriften. Diese Klimaanlage entspricht strengen Sicherheits- und • Das Gelbe/Grüne Kabel ist für die ausschließliche Verwendung Betriebsnormen. als Erdleitung. Für den Installateur oder Bediener dieser Anlage ist es wichtig, sie •...
- Page 16 Wahl des Installationsortes - Innenraumgerät gleichmäßig gekühlt werden kann. VERMEIDEN SIE • Wählen Sie eine Decke, an der der Boden das Gewicht des Gerätes tragen • Direkte Sonneneinstrahlung. kann. • Wärmequellen in der Nähe des Gerätes, die dessen Leistungsfähigkeit • Wählen Sie eine Stelle, von der aus die Rohre und der Wasserablaufschlauch beeinflussen könnten.
- Page 17 INSTRUCCIONES DE INSTALACION - Split cassette - DECLARACION DE CONFORMIDAD Este Producto está marcado porque responde a las Directivas: – Baja Tensión n° 73/23 CEE y 93/68 CEE. – Compatibilidad Electromagnetica n° 89/336 CEE, 92/31 CEE y 93/68 CEE. Esta declaración no tendrá efecto en sólo caso de que se haga un uso diferente al declarado por el Fabricante, y/o por el no respeto, incluso parcial, de las intrucciones de instalación y/o de uso.
- Page 18 DIMENSIONES (mm) Soportes de suspensión Soportes de suspensión Techo Lado aspiración del aire externa SOPORTES DE SUSPENSION Varilla de suspensión Techo Caja de los componentes eléctricos Tuercas y arandelas Lado tubos refrigerantes LADO TUBOS REFRIGERANTE Empalme tubo refrigerante (tubo PEQUEÑO) Empalme tubo refrigerante (tubo GRANDE) Empalme drenaje de la condensación...
- Page 19 ¡IMPORTANTE! • Realizar la puesta a tierra de la unidad siguiendo las normas Leer antes de empezar la instalación eléctricas locales. • El conductor amarillo/verde no se puede utilizar para conexiones que no sean la de tierra. Este sistema de acondicionamiento cumple medidas rígidas de •...
- Page 20 Dónde instalar la unidad interior ES PREFERIBLE • Elegir una posición adecuada desde la que se llegue a todos los EVITAR rincones. • La exposición directa al sol. • Controlar que el techo es lo suficientemente resistente como para • Zonas expuestas a fuentes de calor que puedan dañar la estructura soportar el peso de la unidad.
- Page 21 INDOOR UNIT • UNITÁ INTERNA • UNITE INTERIEURE • INNENEINHEIT • UNIDAD INTERIOR Minimum operation and maintenance area. Area minima di esercizio e manutenzione. Surface minimum de fonctionnement et d’entretien. Raumbedarf des Gerätes. Área mínima de funcionamiento y manutención. SUSPENDING THE UNIT AT THE CEILING This unit uses a drain pump.
- Page 22 Before installing the unit, place the tubes, the electrical wires and the condensate drain pipe in the proper position for the connection. Adjust the distance between the unit and the ceiling (max 23 mm) using the nuts of the four suspension bolts. Verify also the distance between the suspension bracket and the ceiling (min 41 mm);...
- Page 23 INSTALLATION OF THE CONDENSATE DRAIN PIPE. Utilise a hard, well insulated PVC pipe (I.D. 18 mm) and fix it to the unit using a flexible PVC or gummy hose ; tighten firmly with hose bands The connection must be well insulated, using foamed polyethylene (thickness 8mm).
- Page 24 • If it is necessary to increase the height of the drain pipe somewhat, the portion directly after the connection port can be raised a maximum of 25 cm. Do not raise it any higher than 25 , as this could result in water leaks. •...
- Page 25 DUCT FOR FRESH AIR • CONDOTTO PER ARIA ESTERNA DI RINNOVO • CONDUIT POUR LE RENOUVELLEMENT DE L’AIR • LEITUNG FÜR NEUE LUFT • CONDUCTO DE RICAMBIO DEL AIRE • CONDUTA DE RENOVAÇÃO DO AR • AGWGOS AERA ANANEWSHS There is a duct connection port for drawing in fresh air.
- Page 26 Remove the electrical box cover to operate on the terminal strip. Rimuovere il coperchio scatola componenti elettrici per accedere alla morsettiera. Enlever le capot de la boîte des composants électriques. Die Abdeckplatte des Klammbrettes entfernen. Quitar la tapa de la caja de los componentes eléctricos para acceder a la regleta de bornes.
- Page 27 OUTDOOR UNIT • UNITÀ ESTERNA • UNITE EXTERIEUR • AUßENEINHEIT • UNIDAD EXTERIOR Minimum operation and maintenance area Area minima di esercizio e manutenzione. Surface minimum de fonctionnement d’entretien. Raumbedarf des Gerätes. Area mínima de funcionamiento y manutención. Provide a solid base for outdoor unit raised from the ground level. Fix unit to base using 4 anchor bolts.
- Page 28 Use insulated copper tube. Cut approximate 30-50 cm. longer than actual distance between units. min. 8 mm min. 8 mm Utilizzare del tubo in rame isolato. Tagliare con lunghezza maggiorata di 30-50 cm oltre la distanza tra le unità. Utiliser de tube en cuivre isolé. Couper à une longueur de 30-50 cm en plus de la distance entre les unités.
- Page 29 Lubricate Eine gute Kelchung sollte die folgenden Eigenschaften besitzen: - die Oberfläche der Innenseite ist glänzt und glatt - die Kante ist glatt - die Kelchförmig zulaufenden Seiten sind von gleicher Länge. Die Oberfläche, die miteinander in Berührung kommen, mit Frostschutzmittel- Schmierfett schmieren und dann zuschrauben.
- Page 30 Remove caps from service valves of both tubes. Then start vacuum pump and let it run for the time indicated in the table (vacuum 10 mm Hg abs.). Rimuovere i cappucci delle valvole di entrambi i tubi. Quindi avviare la pompa High pressure del vuoto per un tempo consigliato come da tabella (vuoto di 10 mm Hg assoluti).
- Page 31 Turn the service valves stem in counterclockwise to fully open the valves. At this point vacuum pump flexible hose can be disconnected. Replace bonnet and flare nut, tighten them to 200 kg/cm with a torque wrench. Aprire completamente le valvole di servizio (senso antiorario). A questo punto scollegare il flessibile della pompa del vuoto.
- Page 32 The service port on the wide tube service valve uses a Schrader core valve to access the refrigerant system. Therefore, be sure to use a hose connector which has a push-pin inside. La valvola di servizio del rubinetto dell'unità esterna da utilizzare per il vuoto del sistema, il ripristino carica refrigerante e la misurazione della pressione di esercizio è...
- Page 33 SYSTEM WIRING DIAGRAM • COLLEGAMENTI ELETTRICI DEL SISTEMA • BRANCHEMENTS ELECTRIQUES DU SYSTEME • ELEKTRISCHE ANSCHLÜSSE DES SYSTEMS • CONEXIONES ELECTRICAS DEL SISTEMA COOLING ONLY MODELS GRF94-124C5 - GRF95-125L5 MODELLI SOLO FREDDO INDOOR UNIT POWER SUPPLY MODELES FROID SEUL 220-240V ~ 50Hz NUR KÜHLUNG MODELLE OUTDOOR MODELOS SOLO REFRIGERACION...
- Page 34 GRF185R5 1-PHASE MODELS OUTDOOR INDOOR UNIT MODELLI MONOFASE UNIT MODELES MONOPHASES EINPHASENMODELLE MODELOS MONOFÁSICOS NOTE: 3-phase models. If the respective phases of the 3-phase power 3-PHASE MODELS wiring are not connected correctly, a reverse phase will occur and the MODELLI TRIFASE compressor will not start running.
- Page 35 Supply power wire A: Multipolar electric wire. Size and length of the suggested electric wire are showed on table “electrical data”. The wire must be Mod. H05VV-F (according to CEI 20-19 CENELEC HD 22). Make sure the length of the conductors between the fixing point and the terminals allows the straining of the conductors L, N before that of the grounding.
- Page 36 Stromversorgungskabel A: Elektrisches mehradriges Kabel; Querschnitt und Länge des Kabels sind in der Tafel “Elektrische Angabe” angezeigt. Das Kabel soll als H05VV-F-Typ sein (gemäß CEI 20-19 CENELEC HD22). Versichern Sie sich, daß die aktive Leitungen sich vor der Eerdungsleitung spannen. Stromversorgungskabel B: Elektrisches mehradriges Kabel;...
- Page 37 CHECKING THE DRAINAGE • PROVA TUBAZIONE DI DRENAGGIO • CONTROLE DE L’EVACUATION DU CONDENSAT • TEST DER DRÄNLEITUNGEN • CONTROL DEL DRENAJE After piping and wiring are completed, check the correct water drainage. Pour about 1 litre of water into the drain pan; switch on the unit using the power main switch, the pump will start running;...
- Page 38 INSTALLATION OF FRAME/GRILLE ASSEMBLY • INSTALLAZIONE GRUPPO CORNICE/GRIGLIA • INSTALLATION DE L’ENSEMBLE CADRE/GRILLE • AUFSTELLUNG DER RAHMEN/GITTER BAUGRUPPE • INSTALACION DEL CONJUNTO BASTIDOR/REJILLA CAUTION Never attempt to move the flaps with your hands or you may damage them. Instead, use the remote controller if you want to change the direction of air flow. Before installing the frame/grille assembly: 1.
- Page 39 Move the two clips downward, fix the frame to the unit by the two hooks aligning the corner from which the wires exit and the corner with the electrical connectors of the unit. Fix the frame to the unit using the four supplied special screws Connect the electrical connectors Replace the air intake grille verifying that: - The air filter is correctly inserted inside the grille.
- Page 40 REMOTE CONTROL UNIT INSTALLATION • POSIZIONE DI INSTALLAZIONE TELECOMANDO EMPLACEMENT DE LA COMMANDE A DISTANCE • POSITION DER FERNBEDIENUNG • POSICION DE INSTALACION DEL MANDO A DISTANCIA REMOTE CONTROL UNIT INSTALLATION To ensure that the air conditioner operates correctly. DO NOT install the remote control WALL / MURO MUR / PARED unit in the following places:...
- Page 41 PUMP DOWN Pump down means collecting all refrigerant gas in the system quand on doit déplacer le climatiseur, et pour les interventions back into the outdoor unit without losing gas. Pump down is de réparation sur le circuit frigorifique. used when the unit is to be moved of before servicing the Das bedeutet: das Kühlmittel in die Außeneinheit ohne Gas- refrigerant circuit.
- Page 44 In order to carry on a constant improvement, our products can be modified without prior notice. Per garantire un costante miglioramento dei nostri prodotti, ci riserviamo di modificarli senza preavviso. Par souci d’amélioration constante, nos produits peuvent être modifiés sans préavis. Unsere Produkte werden laufend verbessert und können Vorankündigung abgeändert Werden.