Publicité
Les langues disponibles
Les langues disponibles
safety warnings
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock�
Safety guidelines during
power tool operation
•
Fix the workpiece. Use a fixing device or a vice to fix
the work piece for safely and steadily�
• Take necessary and proper safety measures when
harmful, flammable or explosive dust is produced in the
work� For example, dust that may cause cancer is pro-
duced during the operation� Please use dust and chip
collecting device and wear a dust mask in the work�
• Keep workplace tide and clean� The mixed materials
would be extremely dangerous� Light metal dust would
be combusted and explode easily�
• Do not process materials that contain asbestos� As-
bestos is cancerogenic substance�
• Put down the power tool when the saw blade is fully
stopped�
• Do not use power tool when cable is damaged� If
the power wire is damaged or broken in the work, do
not touch it and pull out the plug immediately� Using
broken wire would lead to electric shock easily�
• Keep hands away from sawing area� Hand shall not
hold the lower part of work piece� Your hand would be
cut when it touches saw blade�
• First start the power tool and then put the power tool
of the workpiece to process it� If the saw blade is stuck
in the workpiece and power tool would rebound�
• Attention: the base plate shall cling to the workpiece
during the sawing. If the saw blade is deflected, it
would be broken and power tool would rebound�
• Cut off the power of power tool when work is done
and take the saw blade when the power tool is fully
stopped� The power tool wouldn't rebound in this way
and it can be put down safely�
• Use undamaged and crackles saw blade only�
Bended or dull saw blade would be broken easily and
cause rebound of power tool�
• After the power tool is shut down, do not stop the
moving saw blade by side pressure� The blade saw
would be damaged or broken and further lead to re-
bound in this way�
• Use proper detector to detect whether there is con-
cealed circuit and pipeline in the operation area and ask
the local construction organization for assistance if nec-
essary� In the work, if the cable is cut off, it would cause
fire disaster and electric shock. Damaged gas pipe
would explode� If the water pipe is cut off, it would cause
property losses and electric shock to the operator�
• Fix the saw blade rigidly with the saw holder� Check
the fixing of the saw blade regularly.
• If the used saw blade is not intended for cutting met-
als, remove any metal objects (nails, screws, hinges,
etc�) before work�
• Avoid stopping an power tool motor when loaded�
• During operation watch the position of a power cable
(it should always be positioned behind the power tool)�
Do not allow it to whip around your legs or arms�
Special
• Should power supply fail during work, immediately
turn the power tool's switch "Off" in order to avoid ac-
cidental turning of the power tool on�
• After the power tool is switched off, the saw blade
keeps moving mechanically for some time, therefore
put the power tool aside only after the saw blade is
completely immobile�
• The saw blade gets quite hot during the operation,
therefore do not touch the saw blade until it is com-
pletely cooled off�
Warning: the chemical substances con-
tained in dust generated in sanding, cut-
ting, sawing, grinding, drilling and other
construction industry activities may
result in cancer, congenital deficiency or be harm-
ful to the fertility. The ion of some chemical substanc-
es shall be:
• before any repair and replacement work to the
machine, the power plug must be pulled out firstly;
• the transparent two silicon oxide and other masonry
products in the wall bricks and cement; the chromium
arsenic (CCA) in wood with chemical treatment� The
harm degree of these substances shall depend on the
frequent degree of you carrying out these works� If you
want to reduce the contact with these chemical sub-
stances, please work in the place with ventilation and
you shall use the appliances with safety certificates
(such as the dust mask designed with tiny dust filter).
Following symbols are used in the operation manual,
please remember their meanings� Correct interpreta-
tion of the symbols will allow correct and safe use of
the power tool�
Symbol
English
16
Symbols used in
the manual
Meaning
Sabre saw
Sections marked gray - soft
grip (with insulated surface)�
Serial number sticker:
SAS ��� - model;
XX - date of manufacture;
XXXXXXX - serial number�
Read all safety regulations
and instructions�
Wear safety goggles�
Wear ear protectors�
Publicité
