Favero COIN TIMER Livret D'instructions page 12

in the country. It represents the minimum variation
of all sums: all monetary values set after this
(coins, banknotes, etc.) will be multiples of the
monetary unit. The monetary unit must be
programmed in a way that its value is the same as
the smallest coin that is intended to be used.
One of the following values can be set using the
( ) and ( ) buttons: 0.05 - 0.10 - 0.20 - 0.25 - 0.50 - + –
1 - 2 - 2.50 - 5 - 10 - 20 - 25 - 50 - 100 - 200 - 250.
Examples:
for EURO 0,05, USA 0,10, RUSSIA 1, JAPAN 10.
Press the PROG button to proceed to the following
step.
The following steps from 1 to 9 define the value of
the coins and/or banknotes accepted according to
the type of COIN TIMER used:
COIN TIMER with mechanical coin validator:
used only for step 1.
Set to zero all steps from 2 to 9.
COIN TIMER with electronic coin validator:
step from 1 to 6 correspond to the 6 outlets of the
coin validator.
Set to zero all the steps corresponding to the not
used outlets and the steps 7, 8 and 9.
COIN TIMER with banknote validator:
from 6 to 9 correspond to the outlets from 1 to 4 of
the reader.
Set to zero all the steps from 1 to 5.
COIN TIMER with electonic coin and banknote
validator: the steps from 1 to 6 correspond to the 6
outlets of the coin validator and the steps from 6 to
9 correspond to 4 outlets of the reader. Set to zero
all the steps corresponding to the outlets not used.
1 1 0.05 0.05
COIN 1 VALUE
2 2 0.10 0.10
COIN 2 VALUE
3 0.20 3 0.20
COIN 3 VALUE
4 4 0.50 0.50
COIN 4 VALUE
5 5 1.00 1.00
COIN 5 VALUE
6 6 2.00 2.00
COIN 6 VALUE
7 7 5.00 5.00
BANKNOTE 2 VALUE
8
10.00
BANKNOTE 3 VALUE
9 0.00 9 0.00
BANKNOTE 4 VALUE
The maximum programmable value for the steps
from 1 to 9 is 250 times the value of the monetary
unit indicated in the step " ". To vary quickly, keep
the ( ) or ( ) buttons pressed. If only the coin + –
validator or the banknote validator is used, we
advise you, for more clearness, to set to zero the
value of the step not used.
To proceed to the next step press
it is
the
the steps
U
PROG .
a a 0 0
TIME ZONES CAPACITY
The time zones allow the automatic change of the
tariff in certain hours of the day or of the week. If
the time zones are connected, in the successive
steps the values of the 3 possible tariffs (1, 2 and
3) and the times of change will be defined.
Set with the ( ) or ( ) buttons one of the following +
values, each one corresponds to a different type of
functioning:
0
= disconnected time zones.
always be active and its value will be defined in the
successive step.
1
= connected daily time zones.
week will be the same both for rates and times.
Therefore, afterwards, it will be necessary to
programme only the time zones of one day.
2
= connected weekly time zones.
programme different time zones for the various
days of the week.
To proceed to the next step press
6.00
TARIFF 1
-
In this step the hourly cost of the goods or services
to control is set.
If the time zones are disconnected the TARIFF 1
will always be active.
Use the ( ) e ( ) buttons to set the tariff. + –
To proceed to the next step press
A
If at the " " step the time zones are not connected,
the successive steps will be skipped and the
programming will be ended.
- - 10.00
TARIFF 2
This stage is to be bypassed if the time zones were
not activated in step " ".
Use the ( ) e ( ) buttons to set the tariff. + –
To proceed to the next step press
-
- - 12.00
TARIFF 3
This stage is to be bypassed if the time zones were
not activated in step " ".
Use the ( ) e ( ) buttons to set the tariff. + –
To proceed to the next step press
0 : 00 0 : 00
PROGRAMMING THE
1
-
TIME ZONES
Hours Minutes
Tariff 1, 2 or 3 (
Day (1-7)
This stage is to be bypassed if the time zones were
not activated in step " ". With the ( ) and ( )
buttons you advance, in half hourly periods, the
whole day, while with the
choose the tariff in force at each time among the 3
at your disposal.
11
ENGLISH
–
The TARIFF 1 will
All the days of the
It is possible to
PROG .
(hourly tariff)
PROG .
A
PROG .
A
PROG .
)
A
+
F1 button you can
–