Jet JTSS-1700 Mode D'emploi page 3

3.3 Remaining hazards
When using the machine according to
regulations some remaining hazards
may still exist
The moving sawblade in the work area
can cause injury.
Broken saw blades can cause injuries.
Thrown workpieces can lead to injury
Tipping of the workpiece due to
insufficient support can lead to injury.
Wood chips and sawdust can be
health hazards. Be sure to wear
personal protection gear such as
safety goggles ear- and dust
protection.
Use a suitable dust exhaust system.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.
The type and condition of the
sawblade is important in keeping the
noise level as low as possible.
This does not negate the fact that
extra safety equipment such as ear
protection must be used.
4. Machine specifications
4.1 Technical data
JTSS-1700:
Machine Table
Rear extension table
Right extension table
Sliding table size
Max. travel of sliding table
Max. length of cut
Crosscut table
Sawblade diameter
Blade bore diameter
Blade speed n
0
Scoring blade diameter
Scoring blade bore diameter
Scoring blade speed n
0
Cutting height at 90°/45° 102 / 81 mm
Tilting range of blade
Max. width of rip cut 850 (1270)mm
Dust port diameter
Weight
Mains 230V ~1/N/PE 50Hz
Motor output power 2,2kW (3HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains
Motor output power
Reference current
Extension cord (H07RN-F): 4x1,5mm²
Installation fuse protection
JTSS-2500:
Machine Table
Rear extension table
Right extension table
Sliding table size 2200(2500)x350mm
Max. travel of sliding table
Max. length of cut
Crosscut table
Sawblade diameter
Blade bore diameter
Blade speed n
Scoring blade diameter
Scoring blade bore diameter
Scoring blade speed n
Cutting height at 90°/45° 102 / 81 mm
Tilting range of blade
Max. width of rip cut
Dust port diameter
Weight
Mains
Motor output power
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains
Motor output power 2.9 kW (4 HP) S1
840x550 mm
Reference current
800x550mm
Extension cord (H07RN-F): 4x1,5mm²
830x520mm
Installation fuse protection
1500x350mm
1700mm
JTSS-3200:
1450mm
Machine Table
500 x 500mm
Rear extension table
max 315 mm
Right extension table
30 mm
Sliding table size 3000(3300)x350mm
4000 rpm
Max. travel of sliding table
80mm
Max. length of cut
20mm
Crosscut table
8000 rpm
Sawblade diameter
Blade bore diameter
90°- 45°
Blade speed n
Scoring blade diameter
100mm
Scoring blade bore diameter
410 kg
Scoring blade speed n
Cutting height at 90°/45° 102 / 81 mm
Tilting range of blade
13 A
Max. width of rip cut
16A
Dust port diameter
Weight
400V ~3/PE 50Hz
3 kW (4 HP) S1
6.5 A
16A
840x550 mm
800x550mm
830x520mm
2600mm
2500mm
750x730mm
max 315 mm
30 mm
4000 rpm
0
80mm
20mm
8000 rpm
0
90°- 45°
850 (1270)mm
100mm
520 kg
230V ~1/N/PE 50Hz
2,2kW (3HP) S1
13 A
16A
400V ~3/PE 50Hz
6.5 A
16A
840x550 mm
800x550mm
830x950mm
3350mm
3200mm
1150 x 730mm
max 315 mm
30 mm
4000 rpm
0
80mm
20mm
8000 rpm
0
90°- 45°
1270 mm
100mm
610 kg
3
Mains 230V ~1/N/PE 50Hz
Motor output power 2,2kW (3HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains 400V ~3/PE 50Hz
Motor output power 4.1 kW (5,5 HP)
S1
Reference current
Extension cord (H07RN-F): 4x1,5mm²
Installation fuse protection
4.2 Noise emission
Determined according to EN
1807:1999 (Inspection tolerance 4 dB)
Workpiece plywood 16mm:
T=16mm, L=800mm, moisture 8,5%
Acoustic power level (acc. EN 3746):
Idling
Operating
Acoustic pressure level (EN 11202):
Idling
Operating
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
Although there is a correlation
between emission and imission levels,
these do not constitute a basis for
determining the necessity of additional
safety measures. Workplace
conditions which could influence the
noise imission level include the
duration of resonance, spatial
particulars, other noise sources etc.
For example, the number of machines
and other work being performed. The
permissible workplace levels can vary
from country to country.
This information is intended to allow
the user to make a better estimation
of the hazards and risks involved.
4.3 Dust emission
The circular saw
JTSS-1700/ 2500/ 3200 has been dust
emission inspected.
At an air velocity of 20m/sec on the
dust port dia 100mm:
Vacuum pressure
Volume flow
The TRK-value of 2 mg/m
been exceeded.
13 A
16A
7,7 A
16A
98,3 dB (A)
104 dB (A)
84,4 dB (A)
90,2 dB (A)
800Pa
565 m³/h
3
has not