Télécharger Imprimer la page

Nilfisk Advance Advolution 20 Guide D'utilisation page 5

Masquer les pouces Voir aussi pour Advance Advolution 20:

Publicité

Les langues disponibles

Les langues disponibles

INTRODUCTION
This manual will help you get the most from your Nilfisk-Advance floor machine.
Read it thoroughly before operating the machine.
This product is intended for commercial use only.
PARTS AND SERVICE
Repairs, when required, should be performed by your Authorized Nilfisk-
Advance Service Center, who employs factory trained service personnel, and
maintains an inventory of Nilfisk-Advance original replacement parts and acces-
sories.
Call the Nilfisk-Advance dealer named below for repair parts or service. Please
specify the Model and Serial Number when discussing your machine.
(Dealer, affix service sticker here.)
NAME PLATE
The Model Number and Serial Number of your machine are shown on the
Nameplate on the bottom of the machine. This information is needed when
ordering repair parts for the machine. Use the space below to note the Model
Number and Serial Number of your machine for future reference.
MODEL NUMBER
SERIAL NUMBER
UNCRATE THE MACHINE
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it
can be inspected. Contact the Nilfisk-Advance Customer Service Department
immediately to file a freight damage claim (phone number is provided on the back
cover of this manual).
(A)-KNOW YOUR MACHINE
1
Operator Handle Grips
2
Switch Lever Safety Lock Button
3
Switch Levers - Squeeze - ON / Release - OFF
4
Handle Release Latch
5
Power Cord
6
Operator Handle
7
Motor Brush Wear Indicator Light
PREPARING THE FLOOR
Before each use of this machine, the floor must be clean and completely dry.
Clean the floor with an automatic floor scrubber or a damp mop, using a solution
of water and neutral cleaner.
CAUTION!
This machine should be used only on floors that are coated with
a floor finish suitable for burnishing. Contact your local Nilfisk-
Advance Distributor for further information on floor finishing
products.
PREPARING THE MACHINE FOR USE
WARNING!
This machine contains moving parts. To reduce the risk of injury,
always unplug the power cord before servicing.
B - INSTALLING THE PAD
To install a pad, tip the machine back on it's handle. Remove the Pad Retainer
"A" (in the center of the pad holder) by turning counter-clockwise to loosen. Put
the proper size Pad "B" on the Pad Holder Hub "C". Re-install the Pad Retainer
"A" by turning clockwise to tighten.
OPERATION
1
Unwrap the Power Cord (5) and plug it in to an outlet.
2
Unlatch the Operator Handle (6) by pushing forward on the Handle
Release Latch (4) with your foot. Continue to hold latch (4) while pulling
the handle (6) back. It is normal for the base of the machine to lift off
of the floor slightly when the handle is lowered. It will pull itself down
against the floor as soon as the motor is started.
3
Hold one of the Operator Hand Grips (1) firmly, push the Safety Lock
Button (2) and then compress the Switch Levers (3) to start the motor.
NOTE: The Safety Lock Button (2) will not depress unless the Operator
Handle (6) has been released and tilted back into the operating
position. When the dual controlled Switch Levers (3) are released, the
machine shuts off immediately.
4
Push the machine forward in a straight line, at a slow walking speed.
Overlap each pass about 1-3 inches (25-75 mm).
5
When using a polishing pad, check every 15 minutes to see if the pad
is loaded up with wax and dirt. If it is, turn the pad over to expose the
clean side, or install a clean pad.
FORM NO. 71279A - Advolution 20, 20XP - 5
EN
ENGLISH

Publicité

loading

Ce manuel est également adapté pour:

Advance advolution 20xp01510a01520a