Airxcel 47000 Série Manuel D'utilisation Et Mode D'emploi page 4

IV. For Heating ("Elect-A-Heat" Ceiling Assembly
Model Only) Refer to Figure 1, page 3.
The optional Elect-A-Heat heating assembly is intended to
take the chill out of the indoor air when the air is a few
degrees too cool for comfort. The heating assembly is an
effective "chill chaser". It is not a substitute for a furnace.
Do not expect the heating coil on your heater to glow.
Because the fan draws in cold air and forces it over the coil,
the coil will not turn red. A hint of red may occur where the
moving air does not directly touch the coil. With 9000 series
ceiling assemblies, the heater coil is not externally visible.
A. Turn the selector switch to the "LOW HEAT"
position. At "LOW HEAT", the fan operates on
low speed with heat output at maximum.
B. Rotate the thermostat (temperature control) switch
to the position that is the most comfortable to you.
The thermostat will turn the heater on when the
temperature of the air entering the air
conditioning unit drops below this setting a few
degrees, and automatically turns off when the
temperature of the air entering the air conditioner
rises a few degrees above this setting. The
heater will continue to cycle on and off in this
fashion until the selector switch is turned to
I. Owner
One of the biggest advantages to your new Coleman-Mach air
conditioner is that the maintenance needed to keep the unit in
good care is minimal. In fact about the only thing you, the
owner, must take care of is the cleaning and replacement of
the filters.
Filters are made from long life non-allergenic natural fibers or
foam which can be cleaned and reused, and which completely
filter the circulated air when the air conditioner is in operation.
If the filters are not cleaned at regular intervals, they may
become partially clogged with lint, dirt, grease, etc. A
clogged filter will produce a loss of air volume and may
eventually cause an icing-up of the cooling (evaporator) coil.
IMPORTANT
Do not operate your air conditioner for extended periods
of time without the filter installed.
An even more serious condition occurs when the air
conditioner is operated without a filter. When this
happens the lint, grease, etc. that are normally stopped by
the filter are now accumulating in the cooling coil. This
not only leads to a loss of air volume and a possible icing-
up of the cooling coil, but could also result in serious
damage to the operating components of the air
conditioner.
C.
V.
A.
B.
When the selector switch is in the "LOW FAN" or "HIGH
FAN" position, the blower motor will operate continuously.
IV. MAINTENANCE
We recommend that the filters be cleaned or changed at
least every two weeks when the air conditioner is in
operation.
Cleaning and/or changing the filters:
1.
2.
3.
4.
If replacement filters are necessary, the filters can be
purchased from most Airxcel, Inc. Authorized Service
Centers. It is recommended that spare filters be carried with
the RV at all times to replace worn, torn or deteriorated filters.
4
another mode of operation.
Position the louvers to the desired direction the
discharge air is to flow.
Discharge air temperature can be controlled to some
extent by opening or closing the louvers. When the
louvers are closed, the warmest localized discharge
air is achieved. Fully opened louvers will throw the
warm discharge air to the back and front of the
vehicle for more efficient circulation and faster
warm-up. Although the air temperature is lower
with the louvers fully opened, the heating capacity
is still the same.
For Air Circulation Only (Refer to Figure 1,
page 3).
Turn the selector switch to "LOW FAN" or for
maximum air flow, to "HIGH FAN".
Position the louvers to the desired direction the
discharge air is to flow.
NOTE
Disengage the two 1/4 –turn fasteners that secure the
ceiling assembly grille to the ceiling assembly (See
Figure 2).
Lower the grille and filters from the ceiling assembly.
Take filters out and either clean or exchange them
with other filters (See Figure 2).
If the vehicle is equipped with a flush mount ceiling
assembly, remove the four return air grille screws.
Remove filter from grille and either clean or
exchange with new filters.
NOTE