Technical Data; Guarantee - Clatronic DBS 3001 Mode D'emploi & Garantie

7. The control lamp in the switch of the iron indicates
that it is heating up. As soon as the control lamp goes
off the operating temperature has been reached. Now
you can start ironing.
8. Always remove the mains plug after using the machi-
ne.
Steam Ironing
For this a high temperature is needed.
1. Turn the temperature control (1) to position „• • •"
(cotton, linen).
2. Move both operating switches (10/11) to position I.
When the control lamp (5) lights up there is enough
steam for steam operation.
Warning: The steam is hot!
There is a danger of scalding!
3. You can set the desired quantity of steam with the
steam regulator (9).
4. With the steam jet button
strong jet of steam. Continuous steam is produced by
locking the catch (3) in place.
How can I replenish the water during operation?
If the pressure falls during operation you can fi ll more
water into the tank at the same time.
1. First turn operating switch II
I remains switched to I.
Note: If there is still some residual pressure in the wa-
ter tank, a safety lock prevents the water tank catch
(7) from being opened.
The residual pressure fi rst has to be relieved
before the device can be safely opened.
2. With the steam jet button
the residual steam pressure. When no further steam
comes out of the iron sole plate, turn operating switch
I to 0. Then please remove the mains plug and
carefully open the water tank lock (7).
Warning: The steam is hot!
There is a danger of scalding!
Note: If it is not yet possible to open the lock of the
water tank the device needs a further 2 to 3 minutes
to cool down. Then release the residual pressure
again.
3. With the help of a funnel fi ll freshwater from a measu-
ring beaker into the water tank. Do not overfi ll! Take
care of water splashes that might come out of the
boiler. In order to prevent the water from splashing it
should be fi lled into the funnel slowly after the safety
lock has been opened.
4. Fasten the safety lock again.
5. Insert the power plug back into the socket.
Note: Never open the water tank lock while the
device is being operated.
When ironing at low temperatures, please ensure that
you reduce the quantity of steam or iron without steam
altogether.
05-DBS 3001_A5 25
you can produce a short
to 0. Operating switch
you can now release
Vertical Steam
This can be used to produce a jet of steam in a vertical
direction.
Self-Cleaning
Any lime residues which form in the sole plate are auto-
matically removed due to the heat and steam pressure.
Cleaning
• Always remove the mains lead before cleaning!
• Wait until the machine has cooled down completely.
• Clean the casing with a slightly damp cloth.
• Clean the sole plate and the rest with a slightly damp
cloth. Do not use any abrasive cleaning agents!
• Any residual water can remain in the water tank, but
should be poured out if it has been in the tank for a
prolonged period.

Technical Data

Model: ............................................................... DBS 3001
Power supply: ................................................230 V, 50 Hz
Power consumption: .............................................. 2600 W
Protection class: ............................................................... Ι
Maximum fi lling quantity of the water tank:...........0.7 litres
Steam pressure: ..................................................... 3,5 bar
This device has been tested according to all relevant
current CE guidelines,
such as electromagnetic compatibility and low voltage
directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!

Guarantee

The device supplied by our Company is covered by a
24 month guarantee starting on the date of purchase
(receipt).
During the life of the guarantee any fault of the device or
its accessories *) ascribable to material or manufacturing
defects will be eliminated free of charge by repairing or, at
our discretion, by replacing it. The guarantee services do
not entail an extension of the life of the guarantee nor do
they give rise to any right to a new guarantee!
Proof of the guarantee is provided by the proof of
purchase. Without proof of purchase no free replacement
or repair will be carried out.
If you wish to make a claim under the guarantee please
return the entire machine in the original packaging to
your dealer together with the receipt.
*) Damage to accessories does not mean automatic free
replacement of the whole machine. In such cases please
contact our hotline. Broken glass or breakage of plastic
parts are always subject to a charge.
Defects to consumables or parts subject to wearing
(e.g. motor pistons, kneading blades, drive shafts, spare
remote control, spare toothbrushes, saw blades, etc.) as
well as cleaning, maintenance or the replacement of said
parts are not covered by the guarantee and hence are to
be paid!
25
25.10.2005, 15:05:18 Uhr