Reloop Jockey 3 REMIX Mode D'emploi page 26

nO FUnCTIOn
T16 Beat Jump Forward (+1 beat)
Carries out a beat jump in playback direction.
T17 Beat Jump Forward (+4 beats)
Carries out a beat jump in playback direction.
T18 Roll Mode Button
See chart 4.1.3: -T18-
T19 Mash Mode Button
See chart 4.1.3: -T19-
T20 Hot Cue Buttons
Herewith it is possible to operate the 4 Hot Cues of a track in Traktor.
If a Hot Cue is unassigned (no LED feedback), it is possible to assign it to the
current track's position by pressing one of the Pads -T20-.
T21 Sample Mode Button
Switched the track deck to sample mode. For function assignment please see
chart 4.1.2
T22 Remix Mode Button
Switches the track deck to remix mode. For function assignment, please see
chart 4.1.3
T23 Jog Wheel Mode Buttons
A total of 2 modes are at your disposal that determine the Jog Wheels' -T24-
function.
- Scratch
When activated, the current track can be scratched for as long as the Jog
Wheel's surface is being touched. If only the lateral side is being touched and the
Jog Wheel moved, the current track can be accelerated (clockwise) or decelera-
ted (counterclockwise).
- Search
Allows fast search within a loaded track.
T24 Jog Wheel
Herewith various functions can be controlled. Please refer to the Jog Wheel Mode
Buttons -T23-.
T25 Shift Button
By pressing this button, all the device's control elements receive another function
assignment. The current assignment can be seen on the right side of this chart.
T26 Sync Button
The current track's pitch will be synchronized to the master deck.
T27 Cup Button
As long as this button is being pressed and held, the deck jumps to the last set
cue point and stops. Releasing the button will start playback (depending on
Traktor's setting).
T28 Cue Button
Herewith the cue point will be called up and played as long as the button is being
pressed.
T29 Play/Pause Button
Starts and pauses the track's playback respectivley.
T30 Load Buttons
By pressing this button the selected track will be loaded into the respective deck.
T31 deck Select Switch
Via this switch it is possible to select the ontrolable decks. If the switch is in the
Input position, the mixer can be used as analog mixer.
T32 Gain dial
Adjust the deck's volume with this dial.
T33 eQ dial
Via this dial the high/mid/low frequencies can be adjusted.
T34 Cue Monitor
Via this button it is possible to monitor the selected deck.
T35 Linefader
Adjust the channel's volume with this fader.
T36 Tracklist navigation
- By turning the encoder it is possible to scroll through the track index.
- By pressing the encoder browser view will be maximised.
T37 Master volume
Via this dial the master volume can be adjusted.
This dial is analog and does not send a MIDI signal.
T38 Booth volume
Via this dial the booth output volume can be adjusted.
This dial is analog and does not send a MIDI signal.
T39 Headphones volume
Via this dial the headphones' volume can be adjusted.
This dial is analog and does not send a MIDI signal.
T40 Cue Mix Fading
Via the Cue Mix dial a pre-mix can be simulated via the headphones. In right
position the master signal is audible, in left position the cue signal is audible.
T41 Power Led
The Power LED shows that the Jockey 3 Remix disposes of sufficient power
supply.
T42 MIdI Status Led
The MIDI Status LED shows that MIDI commands are being sent by the controller.
T43 vU Meter
The VU Meter shows the master output's level.
26
FUnCTIOn WITH ACTIvATed SHIFT -T23-
Loop-Out Button
Manually sets a loop ending point. Now the deck is in loop mode; the selected
loop will be repeated permanently. By pressing again you will exit loop mode.
Beat Jump Forward (+16 beats)
Carries out a beat jump in playback direction.
delete Hot Cue
Deletes hot cues by pressing the coresponding button.
Fx Routing Button 1+2
Herewith FX Unit 1 and FX Unit 2, respectively, can be assigned to the current
deck.
Master deck Assignment
The current deck becomes the master deck.
Keylock
(De-)activates Keylock.
Fx Mode Button
Herewith it is possible to switch between Advanced Effect Mode and Chained
Effect Mode.
Tap Button
Determines the track's pitch, depending on how quickly the button will be
repeatedly pressed. Ideally it should be pressed to every beat should the grid not
be fitting.
Favorites navigation
With these buttons it is possible to skip through the favorites.
Faderstart Button
Activates the faderstart function. When active, the track jumps back to the set
floating cue point and starts playback as soon as the linefader -T35- is being
pushed up. (Only Deck A & B)
Folder navigation
- By turning the encoder it is possible to navigate the folder index.
- Pressing the encoder opens and closes the selected index.