Siemens SIMATIC NET SCALANCE XM-400 Manuel De Configuration page 12

Sommaire
7.4.2.1 passive-listening bpdu-vlan-flood ..................................................................................... 380
7.4.2.2 no passive-listening bpdu-vlan-flood ................................................................................ 380
7.4.2.3 passive-listening .............................................................................................................. 381
7.4.2.4 no passive-listening ......................................................................................................... 382
8 Protocoles de réseau.......................................................................................................................... 383
8.1 Commandes en mode de configuration global .................................................................. 384
8.1.1 Phrase d'introduction du mode de configuration global..................................................... 384
8.1.2 ip source-interface ........................................................................................................... 384
8.1.3 no ip source-interface ...................................................................................................... 385
8.2 Protocol IPv4.................................................................................................................... 387
8.2.1 Les commandes "show".................................................................................................... 387
8.2.1.1 show ip dhcp ................................................................................................................... 387
8.2.1.2 show ip route................................................................................................................... 387
8.2.1.3 show ip static route.......................................................................................................... 388
8.2.1.4 show ip gateway .............................................................................................................. 389
8.2.1.5 show ip telnet.................................................................................................................. 389
8.2.1.6 show dcp server............................................................................................................... 390
8.2.1.7 show dcp forwarding ....................................................................................................... 390
8.2.2 Commandes en mode de configuration global .................................................................. 391
8.2.2.1 dcp server........................................................................................................................ 391
8.2.2.2 no dcp server................................................................................................................... 392
8.2.2.3 ip echo-reply.................................................................................................................... 393
8.2.2.4 no ip echo-reply............................................................................................................... 393
8.2.2.5 ip route............................................................................................................................ 394
8.2.2.6 no ip route....................................................................................................................... 395
8.2.2.7 ip routing......................................................................................................................... 396
8.2.2.8 no ip routing.................................................................................................................... 396
8.2.2.9 ipv4 nexthop arp_keep_alive............................................................................................ 397
8.2.2.10 no ipv4 nexthop arp_keep_alive ....................................................................................... 398
8.2.2.11 telnet-server .................................................................................................................... 399
8.2.2.12 no telnet-server ............................................................................................................... 399
8.2.2.13 telnet-server port............................................................................................................. 400
8.2.2.14 no telnet server port ........................................................................................................ 401
8.2.3 Commandes en mode de configuration d'interface ........................................................... 401
8.2.3.1 ip address ........................................................................................................................ 402
8.2.3.2 ip address dhcp................................................................................................................ 403
8.2.3.3 no ip address ................................................................................................................... 404
8.2.3.4 dcp forwarding ................................................................................................................ 405
8.2.4 Commandes en mode de configuration d'interface Loopback............................................ 406
8.2.4.1 ip address ........................................................................................................................ 406
8.2.4.2 no ip address ................................................................................................................... 407
8.3 Protocol IPv6.................................................................................................................... 409
8.3.1 clear ipv6 neighbors ........................................................................................................ 409
8.3.2 clear ipv6 route................................................................................................................ 410
8.3.3 clear ipv6 traffic ............................................................................................................... 410
8.3.4 Les commandes "show".................................................................................................... 411
8.3.4.1 show ipv6 protocols ......................................................................................................... 411
8.3.4.2 show ipv6 neighbors........................................................................................................ 412
8.3.4.3 show ipv6 addr-sel-policy-table ........................................................................................ 412
8.3.4.4 show ipv6 pmtu............................................................................................................... 413
12
SCALANCE XM-400/XR-500 Command Line Interface (CLI)
Manuel de configuration, 03/2021, C79000-G8977-C252-15