Different Shades Of White; Show Programmes And Sequences Of Scenes; Programming Sequences Of Scenes; Synchronous Control Of Several - IMG STAGELINE ODP-483RGBW Mode D'emploi

6.1.1 Colour radiator and stroboscope
In this mode the spotlight constantly radiates
light in an adjustable colour. In addition, the stro-
boscope function can be switched on.
1) Press the button MENU so many times until
the highest menu level is reached (in fig. 2 on
the very left).
2) Press the button UP or DOWN so many times
until the display shows
3) Press the button ENTER. The display now
shows , , , or and a number.
= brightness (0 – 255) of the red LEDs
= brightness of the green LEDs
= brightness of the blue LEDs
= brightness of the white LEDs
= flash frequency (0 – 20 Hz) of the strobo-
scope
4) Use the button ENTER to select the four
adjusting functions one after the other and
the button UP or DOWN to adjust in each
case the brightness or the flash frequency.
Hint: When adjusting the brightness of the red, green
or blue LEDs, not only their brightness changes but
also the shade of colour in case the colours are
mixed. Therefore, first adjust the colour which is to
dominate to the desired brightness and then add the
other two colours. If the intended colour mixture is
white, first adjust the brightness of the green colour
because it appears as the brightest colour to the
human eye. Then add red to result in yellow and
finally add blue to result in white.

6.1.2 Different shades of white

Memorizing 11 shades of colour
In this mode the spotlight radiates white light. 11
different shades of white are memorized which,
however, can be changed. For each shade of
white the red, green, blue and white LEDs can
be adjusted to a different brightness so that this
mode can also be used to memorize 11 individ-
ual shades of colour.
1) Press the button MENU so many times until
the highest menu level is reached (in fig. 2 on
the very left).
2) Press the button UP or DOWN so many times
until the display shows
3) Press the button ENTER. The display now
shows one of the 11 memory locations (
... ) and the LEDs light up in the corre-
sponding brightness.
4) Use the button UP or DOWN to select the
desired shade of white or the memory loca-
tion whose adjustments should be changed.
5) To change an adjustment, select the memory
location, then press the button ENTER. The
display now shows , , or and a number
(0 – 255).
= brightness of the red LEDs
= brightness of the green LEDs
= brightness of the blue LEDs
= brightness of the white LEDs
6) Use the button ENTER to select the four LED
groups one after the other and the button UP or
DOWN to adjust the brightness in each case.
7) To select another shade of white or to change
the adjustments of another memory location,
press the button MENU so that the number of
the memory location is displayed again. Then
repeat steps 4 to 6.
6.1.3 Show programmes and
sequences of scenes
10 show programmes ( ...
orized in the spotlight. Furthermore, 10 se -
quences of scenes ( ...
30 scenes can be programmed individually
( chapter 6.1.4). The show programmes and
sequences of scenes can be started as follows:
1) Press the button MENU so many times until
the highest menu level is reached (in fig. 2 on
the very left).
2) Press the button UP or DOWN so many times
until the display shows
3) Press the button ENTER. The display now
shows the last show programme called (
...
called (
.
4) Select the show programme or the sequence
of scenes with the button UP or DOWN.
The show programmes have the following
sequence:
Show -
programme
AT.01
AT.02
AT.03
AT.04
AT.05
AT.06
AT.07
AT.08
AT.09
AT.10
Fig. 3 Show programmes AT.01 – AT.10

6.1.4 Programming sequences of scenes

10 sequences of scenes can easily be pro-
grammed. A sequence of scenes may consist of
30 scenes as a maximum which change auto-
matically in succession. For each scene, the
colour can be adjusted together with the bright-
ness, the stroboscope function can be activated
at variable flash frequency, the time of scene
and the fading time can be defined.
1) Press the button MENU so many times until
the highest menu level is reached (in fig. 2 on
the very left).
2) Press the button UP or DOWN so many times
until the display shows
3) Press the button ENTER. The display shows
.
the number of the last sequence of scenes
selected (
4) Select the number under which the sequence
of scenes is to be memorized with the button
UP or DOWN and press the button ENTER.
The display shows the number of the first
scene (
5) Each time the button ENTER is pressed, the
following adjusting functions are called in
succession:
= brightness of the red LEDs
= brightness of the green LEDs
= brightness of the blue LEDs
= brightness of the white LEDs
= flash frequency of the stroboscope
= time of scene, 100 = 60 seconds
= fading time
Adjust the desired value in each case with the
button UP or DOWN.
Notes
1. The time of a scene must at least be adjusted to
the value 001, otherwise the scene following it
cannot be programmed.
2. For fading from one scene to the next, a fading
time has to be adjusted for both scenes.
6) After the first scene has been adjusted, press
the button MENU. The display shows the
number of scene again. Select the second
) are mem-
scene with the button UP, press the button
ENTER, adjust the scene and repeat the pro-
) with up to
cedure for all following scenes.
7) After the last scene has been adjusted, mem-
orize the sequence of scenes: Keep the but-
.
) or the last sequence of scenes
... ).
Sequence
stroboscope: white light
fading in / out: red, green, blue, white
change of colour: red, green, blue, white
change of colour: red, off, green, off,
blue, off, white, off
fading: green © red © blue
fading in/out: purple, yellow
fading in / out: purple, yellow
fading in / out: purple
fading in / out: cyan, purple
fading in / out: purple, green
.
... ).
).
ton ENTER pressed for 3 seconds. After
releasing the button, the display must show
the number of the sequence of scenes (
... ), otherwise the button ENTER has
not been pressed long enough.
Notes
1. A sequence of scenes must completely be pro-
grammed before the spotlight is disconnected from the
power supply. After switching on again, a sequence of
scenes cannot be changed any more; it can only be
programmed again. To overwrite a sequence of
scenes, it is not necessary to delete the scenes pro-
grammed before.
2. If the sequences of scenes are not called with the
operational buttons (9) [chapter 6.1.3] but via a DMX
light controller, the DMX channel 2 defines the time of
scene and channel 3 the fading time (chapter 6.3.5).
Channel 2 must at least be adjusted to a DMX value of
001, otherwise the spotlight remains dark.

6.2 Synchronous control of several

spotlights (master / slave mode)
Several ODP-483RGBW can be interconnected.
The master unit can then control all slave units in
sync.
1) Interconnect the spotlights in each case via
the inline jack of the cable DMX OUT (3) and
the plug (6) of the cable DMX IN to a chain.
See chapter 6.3.1 "DMX connection", how-
ever, without paying attention to step 1.
2) The first spotlight of the chain (whose cable
DMX IN is not connected) serves as a master
unit and controls the slave units. Adjust the
slave units to the slave mode:
a) Press the button MENU so many times
until the highest menu level is reached
(in fig. 2 on the very left).
b) Press the button UP or DOWN so many
times until the display shows
c) Press the button ENTER and switch to
with the button UP or DOWN.
3) If sequences of scenes were programmed at
the master unit (chapter 6.1.4), these se -
quences can be copied to the slave units:
a) Press the button MENU at the master unit
so many times until the highest menu level
is reached (in fig. 2 on the very left).
b) Press the button UP or DOWN so many
times until the display shows
c) Press the button ENTER. The display
shows the indication
or .
d) If is not shown, press the button UP
or DOWN as many times as necessary.
e) Press the button ENTER. To start copy-
ing, press the following buttons succes-
sively:
If the display does not light up, first press
any button, then
ENTER, UP, DOWN, UP, DOWN, ENTER.
Pressing the buttons UP and DOWN is
shown in each case by an asterisk ( ) on
the display. While copying, the slave units
show yellow, they show red if an error oc -
curs and green after copying successfully.
f) To switch on the desired operating mode,
press the button MENU so many times
until the display shows
the operating mode with the button UP or
DOWN and activate it with the button
ENTER.
4) For a reset of the slave units back to the pre-
vious programming after copying the se -
quences of scenes, select the menu item
in the menu branch
button ENTER and press the following but-
tons successively:
If the display does not light up, first press any
button, then
ENTER, UP, DOWN, UP, DOWN, ENTER.
GB
.
.
, , ,
again. Select
, press the
11