Device Use; Cleaning And Maintenance - UNIPRODO UNI PUMP 06 Manuel D'utilisation

EN
3. In addition, the LED backlight can be installed
before the nozzle is put onto extension tubes.
4. Place the pump in the water tank so that it is fully
submerged.
5. Be careful for the power cord ends not to get wet.
6. Connect the pump power cable and the LED
backlight cable to the proper connectors on the
control box.
7. Connect the control box cable (11) to the end of
the solar panel cable.

3.3. DEVICE USE

The devices are powered by the energy obtained from
solar radiation. Adjust the solar panel so that it faces
towards the sun. The capacity of the device depends
on the intensity of sunlight and, in the case of UNI_
PUMP_11 and UNI_PUMP_12 models, the degree of
battery charge.
UNI_PUMP_06
The pump switches on automatically when connected
to the solar panel. If the sun is not shining on the panel,
the energy for the pump will not be produced.
UNI_PUMP_11
• To start the pump, press the On / Off button
(8a). When the pump is in operation, the LED (8b)
flashes. After the battery is discharged, the pump
will automatically switch to solar mode and will
run only when there are favorable conditions with
the sufficient amount of sunlight.
• To turn the pump off, press and hold the On /
Off button (8a) for about 3s. The pump will turn
off and the battery will be recharged. When the
battery is being charged, the LED (8b) lights in
a steady mode and changes colours depending
on the charge level.
»
Red LED means low battery, the pump will run for
less than 1hour. Note: it is not recommended to
switch the pump on at low battery level to extend
the battery life.
»
Orange LED means the battery is half-discharged,
the pump will run for about 2-4h.
»
Green LED means the battery is fully charged. The
pump will run for about 4-6h.
• LED backlight turns on only at dusk.
UNI_PUMP_12
• Before the first start-up, fully charge the battery
(about 8 hours if the panel is in full sun).
• To turn the pump on, press the On button (12b),
the LED (12d) will turn green.
• To turn the pump on or off, press the On / Off
button (12h) on the control box panel or the
button (13a) on the remote control. When the
pump is turned on, the LED (12g) will flash green.
It will go out when the pump is switched off.
• The flashing LED (12e) indicates low battery. Do
not switch the pump on. Leave the device for
about 3 hours to charge the battery with the panel
placed in full sunlight.
• The flashing LED (12f) indicates that the battery is
charging.
• Using the knob (12a) on the box or button (13b)
on the remote control, you can adjust the water
flow rate. Note: The higher the flow, the sooner
the device's battery is discharged.
10
• LED backlight turns on automatically when the
pump is turned on. Note: The backlight only works
after dark.
Instructions for using the pumps:
• When the pump is not working despite the panel
being exposed to sunlight, check the connections
and verify the condition of the filter and water
inlets.
• The pump performance is closely related to
weather conditions. The UNI_PUMP_06 pump
operates only and exclusively when powered from
the solar panel. The pump does not work during
cloudy days and at night. The UNI_PUMP_11 and
UNI_PUMP_12 pumps also have a rechargeable
battery. It should be noted that on cloudy days
the battery is not charged during pump operation.

3.4. CLEANING AND MAINTENANCE

a) Before each cleaning, adjustment, exchange of
accessories and when the device is not used,
disconnect it from the power supply from the
solar panel.
b) Use only non-corrosive cleaners to clean the
surface.
c) To clean the surface of the solar panel, use only
a delicate cloth and cleaning liquid dedicated to
the maintenance of solar panels.
d) Store the unit in a dry, cool place, free from
moisture and direct exposure to sunlight.
e) Regularly clean the pump and replace the filter.
In order to disassemble the filter and clean any
impurities from the impeller, remove the cover
(E), remove the filter (D) and the other elements.
Rinse the impeller, housing and filter with clean
running water. If necessary, replace the filter with
a new one.
UNI_PUMP_06
C D E
A
B
UNI_PUMP_11 / UNI_PUMP_12
A D E
C
B
A. Pump motor
B. Impeller
C. Impeller cover
D. Filter
E. Pomp cover
f) The device must be regularly inspected to check
its technical efficiency and spot any damage.
g) Use a soft cloth for cleaning.
h) Do not leave the battery in the device if it will not
be used for a longer period of time.
SAFE REMOVAL OF BATTERIES AND RECHARGEABLE
BATTERIES.
Batteries are installed in the devices and in the remote
control. In the UNI_PUMP_12 model, changing the
battery requires disassembling the front panel. To do
this, undo the screws that fasten the front panel of
the control cabinet to the housing. Gently remove the
front panel, then remove the battery and replace it with
a new one as shown in the figure below.
Recycle batteries with the appropriate organisation or
company.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used to
construct the device can be recycled in accordance with
their markings. By choosing to recycle you are making
a significant contribution to the protection of our
environment. Contact local authorities for information
on your local recycling facility.
11 EN