Product Name; Electrical Safety; Personal Safety; Device Description - UNIPRODO UNI PUMP 06 Manuel D'utilisation

EN
U S E R M A N U A L
TECHNICAL DATA
Parameter Parameter
description value

Product name

Solar pump
Model UNI_ UNI_ UNI_
PUMP_06 PUMP_11 PUMP_12
Power of the 2x6 3 2
solar panel [W]
Powering type Solar Solar Solar
panel panel, panel,
lithium Lead-
battery acid
7,4V/ battery
2000m 6V/4Ah
Ah
Pump power 12÷16 9 6÷10
supply [VDC]
Rated power of 10.1 1.83 2.5
the pump [W]
Maximum 2.5 1.4 1.6
pumping height
[m]
Maximum 1.6 0.75 0.8
projection
height [m]
Max. water flow 1,350 250
[l/h]
Pumped water 40
max. temp. [°C]
Weight [kg] 2.3 0.9 2
1. GENERAL DESCRIPTION
The user manual is designed to assist in the safe and
trouble-free use of the device. The product is designed
and manufactured in accordance with strict technical
guidelines, using state-of-the-art technologies and
components. Additionally, it is produced in compliance
with the most stringent quality standards.
DO NOT USE THE DEVICE UNLESS YOU HAVE
THOROUGHLY READ AND UNDERSTOOD THIS
USER MANUAL.
To increase the product life of the device and to ensure
trouble-free operation, use it in accordance with this
user manual and regularly perform maintenance tasks.
The technical data and specifications in this user manual
are up to date. The manufacturer reserves the right to
make changes associated with quality improvement.
The device is designed to reduce noise emission risks to
a minimum, taking into account technological progress
and noise reduction opportunities.
LEGEND
The product satisfies the relevant safety
standards.
8
Read instructions before use.
The product must be recycled.
WARNING! or CAUTION! or REMEMBER!
Applicable to the given situation (general
warning sign).
PLEASE NOTE! Drawings in this manual are for
illustration purposes only and in some details
may differ from the actual product.
The original operation manual is written in German.
Other language versions are translations from the
German.
2. USAGE SAFETY
ATTENTION!! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in serious injury or even
death.
The terms „device" or „product" are used in the warnings
and instructions to refer to <solar pump>.

2.1. ELECTRICAL SAFETY

a) If you discover damage or irregular operation,
immediately switch the device off and report it to
a supervisor without delay.
b) If there are any doubts as to the correct operation
of the device, contact the manufacturer's support
service.
c) Only the manufacturer's service point may
repair the device. Do not attempt any repairs
independently!
REMEMBER! When using the device, protect
children and other bystanders.

2.2. PERSONAL SAFETY

a) Do not use the device when tired, ill or under
the influence of alcohol, narcotics or medication
which can significantly impair the ability to
operate the device.
b) The device is not designed to be handled by
persons (including children) with limited mental
and sensory functions or persons lacking relevant
experience and/or knowledge unless they are
supervised by a person responsible for their
safety or they have received instruction on how to
operate the device.
c) Do not overestimate your abilities. When using
the device, keep your balance and remain stable
at all times. This will ensure better control over
the device in unexpected situations.
d) The device is not a toy. Children must be
supervised to ensure that they do not play with
the device.
2.3. SAFE DEVICE USE
a) Disconnect the device from the solar panel before
making adjustments, changing attachments or
putting the device away. This preventive measure
reduces the risk of accidental activation.
b) When not in use, store in a safe place, away from
children and people not familiar with the device
who have not read the user manual. The device
may pose a hazard in the hands of inexperienced
users.
c) Keep the device in perfect technical condition.
Before each use check for general damage and
especially check for cracked parts or elements
and for any other conditions which may impact
the safe operation of the device. If damage is
discovered, hand over the device for repair before
use.
d) Device repair or maintenance should be carried
out by qualified persons, only using original spare
parts. This will ensure safe use.
e) To ensure the operational integrity of the device,
do not remove factory-fitted guards and do not
loosen any screws.
f) Clean the device regularly to prevent stubborn
grime from accumulating.
g) It is forbidden to connect the device to power
sources other than a compatible solar panel.
h) Pump clean water of a temperature no higher
than 40°C.
i) It is forbidden to turn the pump on dry before it is
fully immersed in water.
j) It is forbidden to use the device for pumping
contaminated water (e.g. with oil, small particles,
abrasive solids, etc.)
k) Do not use the device for pumping salty water,
caustic substances, flammable liquids, etc.
l) Do not use the device at temperatures below zero
degrees Celsius. Frozen water will damage the
device.
m) Always place the solar panel in a safe place,
protecting it against accidental impact and
damage.
n) It is forbidden to carry the pump or panel by the
cables. Cables must be protected from damage.
ATTENTION! Despite the safe design of the
device and its protective features, and despite
the use of additional elements protecting the
operator, there is still a slight risk of accident or
injury when using the device. Stay alert and use
common sense when using the device.
3. USE GUIDELINES
The device is designed for pumping water in fountains,
ponds, and similar water reservoirs.
The user is liable for any damage resulting from
unintended use of the device.

3.1. DEVICE DESCRIPTION

ATTENTION! This product's view can be found on
the last page of the operating instructions (pp. 60).
1. Pump
2. The pump power cord
3. Solar panel
4. Connecting cable
5. Nozzles
6. Extension tubes
7. Support
8. Control panel
8a. On / off button
8b. LED: battery charge status
8c. Power connector for LED backlight
8d. Pump power connector
9. Power cord for LED backlight
10. LED backlight
11. Cable connecting the control box with the panel
9 EN
12. Control box
12a. Water flow control knob
12b. Device switch on
12c. Device switch off
12d. LED: Power on
12e. LED: Low battery
12f. LED: Charging
12g. LED: Pump on
12h. Pump On / Off button
12i. Power connectors for LED backlight
12j. Pump power connector
13. Remote control
13a. Pump On / Off button
13b. Water flow adjustment button (5 levels)
3.2. PREPARING FOR USE
UNI_PUMP_06
1. Attach the support (7) to the back of the solar
panel (3). Drive the support (7) into the ground
in order to securely position the panel in the
selected place.
2. Connect the solar panels with each other using
the cable (4).
3. Connect the extension tubes (6) and the selected
nozzle (5) to the pump so that the nozzle
protrudes above the surface of water after the
pump is put into the water tank. In the case of
deeper water reservoirs, a raised support should
be prepared for the pump.
4. Place the pump in the water tank so that it is fully
submerged. Be careful for the end of the power
cord not to get wet (2).
5. Connect the pump to the solar panel for power
supply using the cable (2).
UNI_PUMP_11
1. Attach the support (7) to the back of the solar
panel (3). Drive the support (7) into the ground
in order to securely position the panel in the
selected place.
2. Connect the extension tubes (6) and the selected
nozzle (5) to the pump so that the nozzle
protrudes above the surface of water after the
pump is put into the water tank. In the case of
deeper water reservoirs, a raised support should
be prepared for the pump.
3. In addition, the LED backlight can be installed
before the nozzle is put onto extension tubes.
4. Place the pump in the water tank so that it is fully
submerged.
5. Be careful for the power cord ends (2) and (9) not
to get wet.
6. Connect the pump power cable and the LED
backlight cable to the proper connectors on the
panel.
UNI_PUMP_12
1. Attach the support (7) to the back of the solar
panel (3). Drive the support (7) into the ground
in order to securely position the panel in the
selected place.
2. Connect the extension tubes (6) and the selected
nozzle (5) to the pump so that the nozzle
protrudes above the surface of water after the
pump is put into the water tank. In the case of
deeper water reservoirs, a raised support should
be prepared for the pump.