Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
4.
CHARGER LOCATION
4.3
Do not set the battery on top of the charger.
4.4
Do not set the battery charger on flammable items, such as carpeting, upholstery, paper,
cardboard, etc. The charger always generates heat and may damage leather and melt
plastic or rubber.
4.5
Never allow battery acid to drip onto the charger when reading the electrolyte specific
gravity or filling the battery.
4.6
Do not operate the charger in a closed-in area or restrict the ventilation in any way.
5.
DC CONNECTION PRECAUTIONS
5.1
Connect and disconnect the DC output clips only after removing the AC plug from the
electrical outlet. Never allow the clips to touch each other.
5.2
Attach the clips to the battery and chassis, as indicated in sections 6 and 7.
6.
FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE
hood during the charging process, ensure that the hood does not touch the metal part of
the battery clips or cut the insulation of the cables.
6.2
Stay clear of fan blades, belts, pulleys and other parts that can cause injury.
6.3
Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post usually
has a larger diameter than the NEGATIVE (NEG, N, -) post.
6.4
Determine which post of the battery is grounded (connected) to the chassis. If the
negative post is grounded to the chassis (as in most vehicles), see step 6.5. If the positive
post is grounded to the chassis, see step 6.6.
6.5
For a negative-grounded vehicle, connect the POSITIVE (RED) clip from the battery
charger to the POSITIVE (POS, P, +) ungrounded post of the battery. Connect the
NEGATIVE (BLACK) clip to the vehicle chassis or engine block away from the battery. Do
not connect the clip to the carburetor, fuel lines or sheet-metal body parts. Connect to a
heavy-gauge metal part of the frame or engine block.
6.6
For a positive-grounded vehicle, connect the NEGATIVE (BLACK) clip from the battery
charger to the NEGATIVE (NEG, N, -) ungrounded post of the battery. Connect the
POSITIVE (RED) clip to the vehicle chassis or engine block away from the battery. Do
not connect the clip to the carburetor, fuel lines or sheet-metal body parts. Connect to a
heavy-gauge metal part of the frame or engine block.
6.7
Connect charger AC supply cord to electrical outlet.
6.8
When disconnecting the charger, disconnect the AC cord, remove the clip from the vehicle
chassis and then remove the clip from the battery terminal.
7.
FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE
7.2
Attach at least a 24" (61 cm) long 6-gauge (AWG) insulated battery cable to the
NEGATIVE (NEG, N, -) battery post.
All manuals and user guides at all-guides.com
RISK OF EXPLOSION AND CONTACT WITH
BATTERY ACID.
4.1
Locate the charger as far away from the
battery as the DC cables permit.
4.2
Never place the charger directly above the
battery being charged; gases from the battery will
corrode and damage the charger.
A SPARK NEAR THE BATTERY MAY CAUSE A
BATTERY EXPLOSION. TO REDUCE THE RISK
OF A SPARK NEAR THE BATTERY:
6.1
Position the AC and DC cables to reduce the
risk of damage by the hood, door and moving or hot
engine parts. NOTE: If it is necessary to close the
A SPARK NEAR THE BATTERY MAY CAUSE A
BATTERY EXPLOSION. TO REDUCE THE RISK
OF A SPARK NEAR THE BATTERY:
7.1
Check the polarity of the battery posts. The
POSITIVE (POS, P, +) battery post usually has a
larger diameter than the NEGATIVE (NEG, N, -) post.
4
•
•
Publicité
Table des Matières
