Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
1.
Outlet nozzle
2.
Flexible pipe
3.
Clip
4.
Plastic pipe
5.
Clamp
6.
Grip
7.
Pipe
3.2. Preparing for use
3.2.1. APPLIANCE LOCATION
The ambient temperature must not exceed 45°C and the
relative humidity should not exceed 85%. Only use the
device in well-ventilated areas. Do not obstruct the air
outlet of the device. Keep the device away from any hot
surfaces.
3.2.2. ASSEMBLING THE DEVICE
SPRAY NOZZLE ASSEMBLY
•
Remove the bottom cover. Connect the sealing nut
to the rubber tube (don't forget the sealing ring). The
sealing nut should be tightened on the rubber tube
(see picture below).
•
Check if the pressure hose is correctly installed inside
the tank.
•
Attach the hose to the nozzle.
•
Connect the spray tube to the device.
INSTALLATION OF THE SPRAY PIPE
Unscrew the fluid reservoir cap, disconnect the hose and
strainer. Remove the air distributor connector. Then remove
the pressure hose connector with the union nut. Attach
the sprayer adapter to the tank (shown in the figure) and
connect it to the machine.
12
EN
ANTI-ELECTROSTATIC CHAIN
Spraying the chemical granules can cause electrostatic
discharge due to factors such as the type of chemicals,
air temperature, air humidity, etc. To avoid electrostatic
discharge, use only the supplied chain.
FUEL MIXTURE
Never add fuel when the engine is running or hot. To power
the device, use only the fuel/oil mixture in the correct
proportions (gasoline and engine oil dedicated to 2-stroke
engines).The gasoline / oil ratio is 50: 1. Pour the mixture
into the fuel tank.
WARNING! Do not add more oil than recommended and
do not overfill above the fuel tank neck.
3.3. DEVICE USE
NOTE: When pouring the chemical in, make sure the valve
is closed (OFF).
ON
OFF
COLD START
•
After filling the fuel tank, before starting the engine
for the first time, press the fuel primer bubble several
times until the carburettor fills with fuel.
•
Return the switch to its original position.
19.11.2020
•
Place the throttle downwards.
OFF
ON
•
Place the device in an upright position. Hold the top
of the grip firmly with one hand and pull energetically
on the starter handle with the other. If the device does
not start the first time, do not let go of the starter
handle but let it return to the starting position, slowly
controlling its return movement with your hand.
•
After starting the engine, let the machine idle for 2-3
minutes to bring it to operating temperature.
STARTING A WARM ENGINE
•
Leave the throttle completely open.
•
If the engine draws in too much fuel, leave the fuel
tank switch fully closed. Hold the top of the grip firmly
with one hand and pull energetically on the starter
handle with the other hand approx. 5-6 times.
SPRAYING
•
Adjust spraying by repositioning the lever in the three
holes in the rocker arm.
MAX
MIN
19.11.2020
EN
STOPPING THE ENGINE
Move both throttle levers to the lowest positions until the
engine stops. Stop spraying and turn the switch to the off
position. After finishing work, shut off the fuel supply.
Note: When the engine is running, the pipe must be
attached to the machine, otherwise the cooling air will be
reduced, which may damage the engine.
3.4. CLEANING AND MAINTENANCE
a)
Unplug the mains plug and allow the device to cool
completely before each cleaning, adjustment or
replacement of accessories, or if the device is not
being used.
b)
Use only non-corrosive cleaners to clean the surface.
c)
Use only mild, food-safe detergents to wash the
device.
d)
Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
e)
Do not spray the device with a water jet or submerge
it in water.
f)
Do not allow water to get inside the device through
vents in the housing of the device.
g)
Clean the vents with a brush and compressed air.
h)
The device must be regularly inspected to check its
technical efficiency and spot any damage.
i)
Use a soft, damp cloth for cleaning.
j)
Do not use sharp and/or metal objects for cleaning
(e.g. a wire brush or a metal spatula) because they
may damage the surface material of the appliance.
AIR FILTER
Regularly check the condition of the air filter for
contamination that could block it, thus reducing engine
performance and its service life. If the filter is dirty, remove
it and rinse in warm water with detergent, then wipe it with
a dry cloth. A damaged filter must be replaced.
FUEL FILTER
If the fuel filter is blocked, the engine speed and impact
energy of the machine will be reduced. To clean the filter,
unscrew the cap from the tank, pull out the filter through
the hole using a metal hook and clean the filter. If you need
to clean the fuel filter you should also clean the fuel tank.
SPARK PLUG
To ensure proper engine operation, the spark plug gap
must be properly set (0.5-0.7 mm). For a used spark plug,
before checking and adjusting the gap, first use a wire
brush to clean the impurities accumulated on the plug end
(the electrode). Use extraction gasoline if the dirt is difficult
to remove.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used to
construct the device can be recycled in accordance with
their markings. By choosing to recycle you are making
a significant contribution to the protection of our
environment. Contact local authorities for information on
your local recycling facility.
13
Publicité
Table des Matières
