Bosch Indego Notice Originale page 26

Masquer les pouces Voir aussi pour Indego:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 38
OBJ_BUCH-1573-005.book Page 26 Tuesday, December 17, 2013 12:59 PM
26 | English
Explanation of symbols on the machine
General hazard safety alert.
Ensure no exits are blocked or obstructed by the
machine.
Warning: Read user instructions before operating
the machine.
Warning: Operate the disabling device before
working on or lifting the machine.
Caution: Do not touch rotating blades. Sharp
blade(s). Beware of severing toes or fingers.
Wait until all machine components have com-
pletely stopped before touching them. The blades
continue to rotate after the machine is switched
off, a rotating blade can cause injury.
Pay attention that bystanders are not injured
through foreign objects thrown from the ma-
chine.
Warning: Keep a safe distance from the machine
when operating.
Do not ride on the machine.
Battery charger contains a safety transformer.
Operation
 Before working on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the isolator key from the ma-
chine.
 Never allow children or people unfamiliar with these in-
structions to use the machine. Local regulations may re-
strict the age of the operator.
 This machine is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the machine by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the machine.
 The operator or user is responsible for accidents or haz-
ards occurring to other people or their property.
 If any hazard occurs whilst the machine is operating imme-
diately press the red stop button.
 Ensure correct installation of the perimeter wire as in-
structed.
F 016 L81 082 | (17.12.13)
 Check the perimeter wire is fully pegged to the ground
avoiding any slack lengths of wire.
 Periodically inspect the area where the machine is used
and remove all stones, sticks, wires and other foreign ob-
jects.
 Do not run any live mains cables in the working area.
 Periodically inspect to see that the blades, blade bolts and
cutter assembly are not worn or damaged. Replace worn or
damaged blades and bolts in sets to preserve balance.
 Never operate the machine with defective guards or with-
out safety devices.
 Do not put hands or feet near or under rotating parts.
 Never pick up or carry the machine while the motor is run-
ning.
 Do not leave the machine to operate unattended if you
know that there are pets, children or people in the immedi-
ate vicinity.
 Start the machine according to the instructions standing
well away from rotating parts.
 Do not use the product at the same time as a sprinkler or
use the schedule to ensure that the two systems never run
simultaneously.
 Do not modify this product. Unauthorized modifications
may impair the safety of your product and may result in in-
creased noise and vibration.
Remove the isolator key:
– before clearing a blockage,
– before checking, cleaning or working on the machine,
– if the machine vibrates abnormally (stop and check imme-
diately),
– after striking a foreign object. Inspect the machine for
damage and get advice on necessary repairs from your
Bosch Service Centre.
Maintenance
 Always wear gardening gloves when handling or work-
ing near the sharp blades.
 Before working on the machine itself, remove the isola-
tor key.
 Before working on the docking station or power supply,
remove plug from mains.
Clean the exterior of the machine thoroughly using a soft
brush and cloth. Do not use water, solvents or polishes. Re-
move all grass and debris, especially from the ventilation
slots.
Turn the machine on its back and clean the blade area regular-
ly. Use a stiff brush or scraper to remove compacted grass
clippings. (see figure A)
Blades are reversible. (see figure B)
 Keep all nuts, bolts and screws tight to be sure that the ma-
chine is in safe working condition.
 Periodically visually inspect the machine and replace worn
or damaged parts for safety.
 Ensure that only official Bosch replacement parts are used.
 Replace all blades and bolts as a set as required.
Bosch Power Tools

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Indego 1300

Table des Matières