Ecotop Scale Serie Mode D'emploi page 5

PIECES TRINGLERIE AILERON
[A] Aile (avec aileron) .................. 1de chaque
[B] CAP Ø1,0mm (baïonnette) ......................2
[C] Guignol (Plastique) ..................................2
[D] Snap keeper (Plastique) .........................2
[E] Gaine thermorétractable (40x50mm) .....2
[F] Carénage servo aileron (Plastique, blanc)
...................................................... 1de chaque
[G] Clé d'aile Ø8x360mm (Carbone) .............1
[H] Téton calage Ø3mm (Carbone, installé) .2
[I] Gaine thermo. Ø3mm (L=180mm) ........1
PIECES STABILISATEUR
[A] Empennages en V .................1 de chaque
[B] Gouverne (installée) .............1 de chaque
[C] Carénage supérieur (Plastique, blanc) ....1
[D] Couple (CTP 3mm) ..................................1
[E] Gabarit de montage (CTP 3mm) ........ 1set
PIECES TRINGLERIE FUSELAGE
[A] Fuselage fibre de verre ...........................1
[B] Platine servo (CTP 3mm)........................1
[C] Support platine servo (CTP 3mm) ..........1
[D] Support gaine de commande (CTP 3mm) .2
[E] CAP Ø1x1000mm ....................................2
[F] Gaine Ø2.6x900mm ................................2
[G] Guignol (Plastique) .................................2
[H] Snap keeper (Plastique) .........................2
AILERON LINKAGE PARTS
[A] Wing (with aileron) .......................... 1each
[B] Ø1.0mm Music wire (Z bend) .................2
[C] Control horn (Plastic) ..............................2
[D] Snap keeper (Plastic) .............................2
[E] Heat shrink tube (40x50mm, any color) .2
[F] Aileron servo cover (Plastic, white) 1each
[G] Ø8x360mm Wing joiner (Carbon fiber) ...1
[H] Ø3mm Dowel (Carbon fiber, installed) ....2
[I] Ø3mm Heat shrink tube (L=180mm) ......1
STABILIZER PARTS
[A] V-tail stabilizer ................................. 1each
[B] Ruddervator(installed).................... 1each
[C] Tail top cover (Plastic, white) ..................1
[D] Bulkhead (3mm Plywood) .......................1
[E] Stabilizer assembly jig (3mm Plywood) 1set
FUSELAGE LINKAGE PARTS
[A] Fiberglasss fuselage ...............................1
[B] Servo mount (3mm Plywood) .................1
[C] Servo mount support (3mm Plywood) ....1
[D] Guide pipe holder (3mm Plywood) .........2
[E] Ø1x1000mm Music wire .........................2
[F] Ø2.6x900mm Guide pipe ........................2
[G] Control horn (Plastic)..............................2
[H] Snap keeper (Plastic) .............................2
CONTENU DU KIT
PIECES TRAIN D'ATTERRISSAGE
[A] Roue Ø45mm ..........................................1
[B] CAP Ø3x24mm ........................................1
[C] Entretoise de roue (CTP 3mm) ...............1
PIECES VERRIERE
[A] Verrière (Plastique, transparent)............1
[B] Cabine (Plastique, gris) ..........................1
[C] Téton avant verrière (CTP 3mm) ....... 1set
[D] Vis crochet ..............................................1
[E] Support vis crochet (CTP 3mm) .............2
[F] Elastique ..................................................2
[G] Bande autocollante pourtour verrière 1set
[H] Autocollant tableau de bord ...................1
PIECES MONTAGE MOTEUR
[A] Moteur brushless XPower XC3223/10LS
(option) .........................................................1
[B] Couple moteur A (CTP 3mm) ..................1
[C] Couple moteur B (CTP 3mm) ..................1
[D] Vis 3x12mm ............................................4
[E] Ecrou prisonnier M3 ................................4
[F] Platine accu (CTP 3mm) ..........................1
[G] Velcro® autocollant (25x80mm) ...... 1set
KIT CONTENT
LANDING GEAR PARTS
[A] 45mm Wheel............................................1
[B] Ø3x24mm Music wire ..............................1
[C] Wheel spacer (3mm Plywood) .................1
CANOPY PARTS
[A] Canopy (Plastic, clear) ............................1
[B] Cockpit (Plastic, gray) .............................1
[C] Canopy locking tab (3mm Plywood) ... 1set
[D] Eye screw ................................................1
[E] Eye screw mount (3mm Plywood)...........2
[F] Rubber band ............................................2
[G] Canopy Frame Sticker ........................ 1set
[H] Instrument Panel Sticker .........................1
MOTOR MOUNTING PARTS
[A] Brushless motor XPower XC3223/10LS
(optional) .......................................................1
[B] Motor mount A (3mm Plywood) ..............1
[C] Motor mount B (3mm Plywood) ..............1
[D] 3x12mm Screw .......................................4
[E] 3mm Blind nut .........................................4
[F] Battery mount (3mm Plywood) ...............1
[G] Adhesive based Velcro® (25x80mm) 1set
5
PIECES HELICE REPLIABLE (Options)
[A] Pale hélice repliable 11x9 .......................2
[B] Porte-pales 4mm ....................................1
[C] Axe 3x12mm ...........................................2
[D] Circlip ......................................................2
[E] Vis sans tête 4mm ...................................2
AUTRES PIECES
Manuel de montage .......................................1
Planche autocollants .....................................1
FOLDING PROPELLER PARTS (Optional)
[A] 11x9 Folding propeller blade ..................2
[B] 4mmTM Hub ............................................1
[C] 3x12mm Pin ............................................2
[D] E ring.......................................................2
[E] 4mm Set screw ........................................2
OTHER PARTS
Construction guide book ...............................1
Color sticker ...................................................1