Urmet BiBus II 1072/17 Mode D'emploi page 22

In the case of 1st edition systems, the module
will be automatically configured as a main
station and should not be changed.
The following message will appear on the display:
C..MOD..TYPE:
<MA.> <SEC>
Press. .and. .to.select.and.press.
The system will automatically go back to the main
menu after a confirmation tone.
1st. edition. system:. this. programming. is. not.
required..
Station number (ID)
A. number. from. 1. to. 1. is. assigned. to. each. main.
calling.station..A.number.from.0.to.9.is.assigned.to.
each.secondary.station..The.secondary.number.is.
in the range from A to J in systems with alphabetic
prefix. A to J programmed on a secondary station
will automatically be reprogrammed as a prefix code
format. ID from 0 to 9 on a secondary station will
automatically.be.reprogrammed.as.a.numeric.code.
format.
The following message will appear on the display:
==. Station.n°.. . ==
Station.
Enter.the.station.number.and.press.
Press. to cancel the entry. The system will
automatically. go. back. to. the. main. menu. after. a.
confirmation tone.
1st.edition.system:.the.station.number.must.be.in.the.
range.from.1.to.1.(there.are.no.secondary.stations.
in.the.system)..Assign.15.as.station.number.to.use.
the.clone.function..
Busy time
The busy time is split into two sub-menus.
The following message will appear on the display:
==. BUSY.TIME. . ==
PICKUP.TIME.
==. BUSY.TIME. . ==
BUSY.TIME. .

to confirm.
1
to confirm.
. .
↓
. . .
↑
Press. .and. .to.select.the.sub-menu.and.press.
. to confirm.
Off-hook stand-by time
The.off-hook.stand-by.time.is.the.maximum.time.of.
a call in which the user can answer the door phone.
All other calling stations will be busy during this
time..All.devices.in.the.system.must.have.the.same.
off-hook waiting time. The following message will
appear.on.the.display:.
PICKUP.TIME:.... . . 0S
<10><20><30><40>
Press. .and. .to.select.and.press.
The system will automatically go back to the main
menu after a confirmation tone.
Minimum conversation time (busy)
When a user is called and answers the door phone,
all other call stations will be busy for the minimum
programmed. conversation. time.. A. communication.
that has just started cannot be interrupted. All
devices.in.the.system.must.have.the.same.minimum.
conversation time (busy time). The following
message will appear on the display:
BUSY.TIME:... . . . 0S
<10><20><30><40>
Press. .and. .to.select.and.press.
The system will automatically go back to the main
menu after a confirmation tone.
Door lock activation time
The.relay.controlling.the.door.lock.can.be.managed.
in. pulse. mode. (approximately. 500. ms). or. stabile.
mode (from 1 to 30 s). The following message will
appear.on.the.display:.
=. Door.op..time. .
0.seconds
Enter. the. number. of. seconds. and. press.
confirm. Press . to. cancel. the. entry.. The. system.
will automatically go back to the main menu after a
confirmation tone.
Door opener codes
The.eight.generic.door.opener.codes.can.be.stored.
in.sequence.
The following message will appear on the display:
to confirm.
to confirm.
=
. to.
DS107-035