Binks MAG II Mode D'installation page 10

MAG II AUTOMATIC MANIFOLD MOUNTED AIR-ASSISTED HVLP SPRAY GUN
TWIST TIP SELECTION CHARTS
Fan width based on 2200 PSI with latex
paint 12" from surface. Actual results may
vary, depending on material viscosity.
PART NUMBER DESCRIPTION
9-307-75 TWIST TIP
9-309-75 TWIST TIP
9-409-75 TWIST TIP
9-509-75 TWIST TIP
9-211-75 TWIST TIP
9-311-75 TWIST TIP
9-411-75 TWIST TIP
9-511-75 TWIST TIP
9-611-75 TWIST TIP
9-213-75 TWIST TIP
9-313-75 TWIST TIP
9-413-75 TWIST TIP
9-513-75 TWIST TIP
9-613-75 TWIST TIP
9-713-75 TWIST TIP
9-215-75 TWIST TIP
9-315-75 TWIST TIP
9-415-75 TWIST TIP
9-515-75 TWIST TIP
9-615-75 TWIST TIP
9-715-75 TWIST TIP
9-317-75 TWIST TIP
9-417-75 TWIST TIP
9-517-75 TWIST TIP
9-617-75 TWIST TIP
9-717-75 TWIST TIP
9-419-75 TWIST TIP
9-519-75 TWIST TIP
9-619-75 TWIST TIP
9-521-75 TWIST TIP
9-621-75 TWIST TIP
9-523-75 TWIST TIP
9-623-75 TWIST TIP
9-525-75 TWIST TIP
9-625-75 TWIST TIP
9-627-75 TWIST TIP
9-435-75 TWIST TIP
9-631-75 TWIST TIP
9-635-75 TWIST TIP
FINE FINISH FLAT TIP SELECTION CHARTS
Fan width based on 1000 PSI with water
12" from surface. Actual results may
vary, depending on material viscosity.
PART NUMBER DESCRIPTION
9-0909-F FINE FINISH TIP
9-0911-F FINE FINISH TIP
9-1109-F FINE FINISH TIP
9-1111-F FINE FINISH TIP
9-1113-F FINE FINISH TIP
9-1115-F FINE FINISH TIP
9-1309-F FINE FINISH TIP
9-1311-F FINE FINISH TIP
9-1313-F FINE FINISH TIP
9-1315-F FINE FINISH TIP
9-1509-F FINE FINISH TIP
9-1511-F FINE FINISH TIP
9-1513-F FINE FINISH TIP
9-1515-F FINE FINISH TIP
9-1517-F FINE FINISH TIP
9-1709-F FINE FINISH TIP
9-1711-F FINE FINISH TIP
9-1713-F FINE FINISH TIP
9-1715-F FINE FINISH TIP
9-1717-F FINE FINISH TIP
10
FAN GPM
WIDTH CAPACITY
ORIFICE (IN.) @2200 PSI
0.007 6 0.05
0.009 6 0.09
0.009 8 0.09
0.009 10 0.09
0.011 4 0.12
0.011 6 0.12
0.011 8 0.12
0.011 10 0.12
0.011 12 0.12
0.013 4 0.18
0.013 6 0.18
0.013 8 0.18
0.013 10 0.18
0.013 12 0.18
0.013 14 0.18
0.015 4 0.24
0.015 6 0.24
0.015 8 0.24
0.015 10 0.24
0.015 12 0.24
0.015 14 0.24
0.017 6 0.31
0.017 8 0.31
0.017 10 0.31
0.017 12 0.31
0.017 14 0.31
0.019 8 0.38
0.019 10 0.38
0.019 12 0.38
0.021 10 0.47
0.021 12 0.47
0.023 10 0.57
0.023 12 0.57
0.025 10 0.67
0.025 12 0.67
0.027 12 0.74
0.035 8 1.31
0.031 12 1.03
0.035 12 1.31
GPM
FAN CAPACITY
WIDTH @500 PSI
ORIFICE (IN.) WATER
0.009 9 0.039
0.009 11 0.039
0.011 9 0.06
0.011 11 0.06
0.011 13 0.06
0.011 15 0.06
0.013 9 0.09
0.013 11 0.09
0.013 13 0.09
0.013 15 0.09
0.015 9 0.12
0.015 11 0.12
0.015 13 0.12
0.015 15 0.12
0.015 17 0.12
0.017 9 0.16
0.017 11 0.16
0.017 13 0.16
0.017 15 0.16
0.017 17 0.16
STANDARD FLAT TIP SELECTION CHARTS
Fan width based on 1000 PSI with water
12" from surface. Actual results may
vary, depending on material viscosity.
PART NUMBER DESCRIPTION
114-00702 TIP ASSEMBLY
114-00704 TIP ASSEMBLY
114-00706 TIP ASSEMBLY
114-00708 TIP ASSEMBLY
114-00902 TIP ASSEMBLY
114-00906 TIP ASSEMBLY
114-00908 TIP ASSEMBLY
114-00910 TIP ASSEMBLY
114-00912 TIP ASSEMBLY
114-01104 TIP ASSEMBLY
114-01106 TIP ASSEMBLY
114-01108 TIP ASSEMBLY
114-01110 TIP ASSEMBLY
114-01112 TIP ASSEMBLY
114-01114 TIP ASSEMBLY
114-01304 TIP ASSEMBLY
114-01306 TIP ASSEMBLY
114-01308 TIP ASSEMBLY
114-01310 TIP ASSEMBLY
114-01312 TIP ASSEMBLY
114-01314 TIP ASSEMBLY
114-01316 TIP ASSEMBLY
114-01506 TIP ASSEMBLY
114-01508 TIP ASSEMBLY
114-01510 TIP ASSEMBLY
114-01512 TIP ASSEMBLY
114-01514 TIP ASSEMBLY
114-01516 TIP ASSEMBLY
114-01518 TIP ASSEMBLY
114-01706 TIP ASSEMBLY
114-01708 TIP ASSEMBLY
114-01710 TIP ASSEMBLY
114-01712 TIP ASSEMBLY
114-01714 TIP ASSEMBLY
114-01716 TIP ASSEMBLY
114-01718 TIP ASSEMBLY
114-01906 TIP ASSEMBLY
114-01908 TIP ASSEMBLY
114-01910 TIP ASSEMBLY
114-01912 TIP ASSEMBLY
114-01914 TIP ASSEMBLY
114-01916 TIP ASSEMBLY
114-01918 TIP ASSEMBLY
114-02110 TIP ASSEMBLY
114-02112 TIP ASSEMBLY
114-02114 TIP ASSEMBLY
114-02116 TIP ASSEMBLY
114-02118 TIP ASSEMBLY
114-02410 TIP ASSEMBLY
114-02412 TIP ASSEMBLY
114-02414 TIP ASSEMBLY
114-02416 TIP ASSEMBLY
114-02418 TIP ASSEMBLY
114-02710 TIP ASSEMBLY
114-02712 TIP ASSEMBLY
114-02714 TIP ASSEMBLY
114-02716 TIP ASSEMBLY
114-02718 TIP ASSEMBLY
TWIST TIP NOTE
When switching from flat tip to twist tip, increase pattern
size by 2 inches and use air adjustment to turn down to
desired size.
GPM
FAN CAPACITY
WIDTH @500 PSI
ORIFICE (IN.) WATER
.007 2 .028
.007 4 .028
.007 6 .028
.007 8 .028
.009 2 .039
.009 6 .039
.009 8 .039
.009 10 .039
.009 12 .039
.011 4 .060
.011 6 .060
.011 8 .060
.011 10 .060
.011 12 .060
.011 14 .060
.013 4 .090
.013 6 .090
.013 8 .090
.013 10 .090
.013 12 .090
.013 14 .090
.013 16 .090
.015 6 .120
.015 8 .120
.015 10 .120
.015 12 .120
.015 14 .120
.015 16 .120
.015 18 .120
.017 6 .160
.017 8 .160
.017 10 .160
.017 12 .160
.017 14 .160
.017 16 .160
.017 18 .160
.019 6 .190
.019 8 .190
.019 10 .190
.019 12 .190
.019 14 .190
.019 16 .190
.019 18 .190
.021 10 .240
.021 12 .240
.021 14 .240
.021 16 .240
.021 18 .240
.024 10 .310
.024 12 .310
.024 14 .310
.024 16 .310
.024 18 .310
.027 10 .385
.027 12 .385
.027 14 .385
.027 16 .385
.027 18 .385