Charging Instructions - Spyder ELECTRA WITH EYE Manuel De L'utilisateur

CHARGING INSTRUCTIONS

Spyder 9.6volt Battery (US LED) optional accessory
To charge a Spyder 9.6 NiMH battery, the circuit board must be in the OFF position. Spyder batteries (JE1015) are not
fully charged when purchased. Using the supplied Spyder LED A/C Charger (JE1029), plug the charger into the charger
port located at the rear of the trigger frame. For a complete charge, Kingman recommends a charging time of
STEP 1 Plug the Spyder LED A/C charger into a power outlet.
STEP 2 Connect the Spyder A/C charger cord to the rear of the markers trigger frame's charging port..
STEP 3 The LED indicator on the Spyder LED A/C charger will display RED when the battery is charging.
STEP 4 The LED indicator on the Spyder LED A/C charger will display GREEN when the battery is fully charged.
STEP 5 Unplug the Spyder LED A/C charger cord from the rear of the markers trigger frame's charging port
after charging.
STEP 6 Remove the Spyder LED A/C charger from the power outlet.
IMPORTANT: Never charge the battery for over 24 hours, as you will risk damaging the battery and/or electronics.
HELPFUL TIP: It is recommended that the battery be charged prior to use in order to ensure maximum performance,
especially if the battery has not been used in over a week.
5000-6000 shots, depending on your firing methods or firing mode in use. Under normal use and charging
conditions the expected life of the Spyder battery is approximately 700-1000 charging cycles.
To avoid any risks of having the Battery explode or the Circuit Board burned: charge only Spyder 9.6volt NiMH
Batteries in Spyder electronic frames.
IMPORTANT
• DO NOT attempt to recharge any Alkaline or any other type of battery in the Spyder electronic frame.
• DO NOT try to recharge batteries that are rusted, corroded, damaged or leaking.
• FAILURE to follow any of the instructions will
Kingman will not be held liable for any injury or damages from the improper use of this product. This accessory is not
intended for use with any other product other than what Kingman designed it for.
Spyder 9.6volt Battery (EU) optional accessory
To charge a Spyder 9.6 NiMH battery, the circuit board must be in the OFF position. Spyder batteries (JE1015) are
not fully charged when purchased. Using the supplied A/C Charger (JE1025), plug the charger into the charger port
located at the rear of the trigger frame. For a complete charge, Kingman recommends a charging time of
IMPORTANT: Never charge the battery for over 24 hours, as you will risk damaging the battery and/or electronics.
HELPFUL TIP: It is recommended that the battery be charged prior to use in order to ensure maximum performance,
especially if the battery has not been used in over a week.
NOTE: A fully charged Spyder battery will last about 5000-6000 shots, depending on your firing methods or firing
mode in use. Under normal use and charging conditions the expected life of the Spyder battery is approximately
700-1000 charging cycles.
To avoid any risks of having the Battery explode or the Circuit Board burned: charge only Spyder 9.6volt NiMH
Batteries in Spyder electronic frames.
IMPORTANT
• DO NOT attempt to recharge any Alkaline or any other type of battery in the Spyder electronic frame.
• DO NOT try to recharge batteries that are rusted, corroded, damaged or leaking.
• FAILURE to follow any of the instructions will
Kingman will not be held liable for any injury or damages from the improper use of this product. This accessory is not
intended for use with any other product other than what Kingman designed it for.
NOTE: A fully charged Spyder battery will last about
VOID ALL WARRANTIES AND LIABILTIES
VOID ALL WARRANTIES AND LIABILTIES
English
6-8 hours.
from Kingman.
6-8 hours.
from Kingman.
6