Remote Control - Revell Control Tritan Mode D'emploi

1 MUlTICopTer
1A Motors 1B Battery compartments

2 reMoTe CoNTrol

2A Controller for thrust and rotation
2B Control mode switch
2C Trim reset
2D Power LED
2E ON/OFF switch
2F Button for position sensor calibration
2G Flip button
2H Trim buttons for forwards and
backwards
3 INSerTINg BaTTerIeS (reMoTe CoNTrol)
3A To open the battery 3B Insert 4 x 1.5 V AA batteries
compartment, unscrew
and pay attention to the
the securing screw
polarity, as shown in the
anticlockwise then pull
battery compartment.
down the latch of the
flap down.
4 ChargINg The MUlTICopTer
Attention: The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
• Unplug the multicopter from the battery, switch off the remote control and insert the
USB charger in a USB hub or similar. The control LEDs on the charger are off (4A).
• Remove both batteries from the compartment (do not hold by the cable!) (4B).
• Now plug both batteries into the sides of the charger Pay attention to the polarity.
Please do not use force. The LED on the charger will light up red when charging
begins (4C).
• The charging process lasts approx. 150 minutes and must be continuously monitored.
The red LED on the charger goes out as soon as the charging process is finished.
• Alternatively, the USB charger can also be plugged directly into the remote control
(4D). For this purpose, switch on the remote control and move the left thrust
controller briefly to full throttle and then back.
16
1C Status LED
2I Controller for forwards and backwards
as well as sideways
2J Trim buttons for sideways flight
2K Trim buttons for rotation
2L Buttons for flip function
2M Battery compartment lock
2N Battery compartment securing screw
2O Battery compartment
3C Replace the cover
and screw in the
securing screw
clockwise.
After a charge time of approx. 150 minutes the multicopter can fly for
approx. 5 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
5 STarT preparaTIoN
The thrust controller (left controller on the remote control) must point down before
switching on (5A). Then set the ON/OFF switch (5B) on the remote control to the „ON"
position and the Power LED begins to blink (5C).Connect the two battery cables with
the connection cables (5D). Now the blue status LEDs on the rear of the multicopter
blink. Once they are constantly illuminated blue, the model is ready. Place the
multicopter on the ground so that the tail faces you and the two propellers arranged
on top of one another face forward.
Attention! Make sure that you place your multicopter on a level surface – the control
electronics align their neutral position to the ground!
6 TrIM aDJUSTMeNT oF The CoNTrol
The correct trim is a basic requirement for fault-free flying behaviour of the multicopter.
Its adjustment is simple, but it requires some patience and a feel for it. Please observe
the following instructions precisely: Carefully move the thrust control up and raise the
multicopter approximately 0.5 to 1 metre in altitude.
6A If the multicopter moves by itself slowly or quickly to the left or right ...
press the trim adjustment for banking incrementally in the opposite direction.
6B If the multicopter moves by itself slowly or quickly around its own axis ...
press the trim adjustment for rotation incrementally in the opposite direction.
6C If the multicopter moves by itself slowly or quickly forwards or backwards ...
press the trim adjustment for forward and backwards flight incrementally in the
opposite direction.
17