Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
To reduce the risk of injury, always unplug tool before
attaching or removing accessories. Use only specifi cally
recommended accessories. Others may be hazardous.
Using the Transport Lock
The transport lock secures the handle for transporting and storing the
tool. To release the transport lock, push down the handle and pull out the
transport lock. To lock the transport lock, push down the handle and push
in the transport lock.
To reduce the risk of injury, do not use the FIXTEC nut on any
other tool. The FIXTEC nut is specifi cally designed for this
application and may be hazardous when used on other tools.
Using the FIXTEC Nut
The FIXTEC nut allows for wheel changes without tools. To use the FIXTEC
nut, pull out the hinged latch and spin off the nut. To replace the nut, hand
tighten the nut until it is secure. Do not over tighten the nut. This may damage
the wheel and the fl anges. When the nut is tight, snap the hinged latch back
into position. Make sure the hinged latch is down before using the tool.
To reduce the risk of injury, use only the proper TYPE 1 wheels
made for this machine. DO NOT USE TOOTHED BLADES.
Removing and Installing Cut-Off Wheels (Fig. 1)
The cut-off machine is supplied with the abrasive cut-off wheel
installed. MILWAUKEE recommends using only MILWAUKEE 14"
Abrasive Cut-Off Wheels, 3/32" wide with this tool. Before operating
the tool, make sure the wheel is in good condition as described in the
"Specifi c Safety Instructions - Abrasive Cut-Off Machines".
Fig. 1
Moveable portion of guard
Inner fl ange
To change wheels:
1.
Unplug tool.
2.
Release the transport lock.
page 6
WARNING
WARNING
WARNING
Abrasive cut-off
wheel
Outer fl ange
FIXTEC nut
or
4-hole fl ange nut
OPERATION
3.
Pull back the moveable portion of the guard to expose the wheel arbor
and nut.
P r e s s d o w n t h e s p i n d l e l o c k l e v e r a n d l o o s e n t h e n u t
(counterclockwise).
4.
Remove the nut, outer fl ange and cut-off wheel.
5.
Check the two (2) wheel fl anges to be sure they are in good condition.
Remove any nicks or burrs, which could cause uneven cutting pressure
and result in wheel damage.
6.
Install the cut-off wheel, outer fl ange and nut (Fig. 1).
7.
Press down the spindle lock lever while tightening the nut
(clockwise).
NOTE: Hand tighten the FIXTEC nut fi rmly, but do not use excessive
pressure. Overtightening the FIXTEC nut may damage the wheel and
fl anges. Do not use any tool to tighten the FIXTEC nut. Hand tighten
only.
8.
Check the wheel for free rotation after installation.
9.
Allow the moveable portion of the guard to return to its original posi-
tion.
10. Before starting a cut, step back and out of line from the tool wheel and
make a trial run to confi rm that the wheel is in good condition. When
replacing a cut-off wheel, run the tool for over 3 minutes. When starting
routine work, run the tool for over 1 minute.
Adjusting the Depth of Cut (Fig. 2)
Use the depth adjustment to change the depth of cut. When ad-
justed properly, the depth adjustment bolt prevents the cut-off
wheel from contacting the surface under the base during cutting.
Cut-off wheels wear down as they are used and the depth of cut may need
to be increased.
1.
To adjust the depth of cut, loosen the wing nut.
2.
Turn the depth adjustment bolt to achieve the desired depth of cut.
3.
Tighten the wing nut.
Fig. 2
Wing nut
Using the Quick Release Lever (Fig. 3)
Fig. 3
1.
To release the quick release lever, rotate the lever fully to the left.
2.
To lock the quick release lever, rotate the lever fully to the right.
Depth adjustment bolt
Release
Lock
Publicité
Table des Matières
