Campbell Hausfeld VS260000KB Instructions D'utilisation page 3

Introduction
(Continued)
prevents air in the tank from flowing
back into the compressor pump.
Handle - Designed to move the
compressor.
Never use the
WARNING
!
handle to lift the
unit completely off the ground.
Belt Guard - Covers the belt, motor
pulley and flywheel.
WARNING
!
Never
operate compressor
without a beltguard. This
unit can start
automatically without
warning. Personal injury or property
damage could occur from contact with
moving parts.
Tank Drain Valve - This valve is
located on the bottom of the tank. Use
this valve to drain moisture from the
tank daily to reduce the risk of
corrosion.
Reduce tank pressure below 10 psi,
then drain moisture from tank daily to
avoid tank corrosion. Drain moisture
from tank(s) by opening the drain
valve located underneath the tank.
Tank Pressure Gauge - Indicates
amount of air pressure stored in tank.
Hose Pressure Gauge - Indicates
amount of air pressure in hose used to
operate tools. This pressure is increased
or decreased by the regulator.
Assembly
HORIZONTAL TANK UNITS ONLY
HANDLE
1. Remove the handle screw from the
tank baseplate, if preinstalled.
2. Insert handle into both sides of tank
baseplate. Squeeze handle to fit into
special openings in baseplate (See
Figure 2).
Handle
Bracket
Figure 2
3. Place a short piece of wood against
end of handle and tap with a mallet
or hammer until the hole in the
handle lines up with the hole in the
baseplate.
4. Insert and tighten the handle screw
into the hole in the baseplate and
through the handle. Make sure the
screw goes through the handle.
WHEEL ASSEMBLY
The items marked with an asterisk (*) in
Figure 3 were shipped loose with the
unit. Assemble as follows:
1. Insert shoulder bolt through wheel
hub with the bolt head on the
opposite side of the protruding hub
section.
2. For the 8 inch diameter wheels,
insert the shoulder bolt in the low-
est hole of the tank axle iron and
tightly secure with locknut.
3. For the 10 inch diameter wheels,
insert the shoulder bolt in the upper
hole in the tank axle iron and
tightly secure with the locknut.
Repeat this step on the opposite
side.
*
Lock
Nut
Figure 3 - Wheel Assembly
When assembled, the tank must sit
level or slope slightly towards the tank
drain valve to allow tank to drain
properly.
VERTICAL TANK UNITS ONLY
Tank
HANDLE ASSEMBLY
Baseplate
Insert four handle screws through holes
in handle and tighten to tank baseplate
(See Figure 4).
FOOT ASSEMBLY
The items marked with an asterisk (*)
Handle
were shipped loose with the unit (See
Screw
Figure 5 and Figure 6).
1. Tilt unit to allow access to front foot
Rubber
and secure properly to ensure unit
Foot
does not tip over.
Shoulder
bolt
Wheel
*
3
Portable Air Compressors
Handle
Handle
Screws
Figure 4
2. Insert bolt through foot and
bracket. The foot should be on the
lower side of bracket.
3. Tightly secure with the lock nut.
Repeat on opposite side.
WHEEL ASSEMBLY
The items marked with an asterisk (*)
were shipped loose with the unit (See
Figure 5).
1. Insert shoulder bolt through wheel
hub. The bolt hex head should be
on the opposite side of protruding
hub center.
2. Feed the shoulder bolt through the
hole on the tank axle iron and
tightly secure with the locknut.
Repeat on the opposite side.
Nut*
Foot*
Bolt* Shoulder
Bolt*
Figure 5 - Foot and Wheel Assembly
Nut
Washer
Rubber Feet
Bolt
Figure 6
LUBRICATION
THIS UNIT IS
CAUTION
!
SHIPPED WITHOUT
OIL! Follow lubrication instructions
before operating compressor.
www.chpower.com
Tank Baseplate
Lock
Nut*
Wheel*