Information About Special Risks With Electrical Energy; Gas, Dust, Steam, Smoke; Noise - GÖLZ FS125 Mode D'emploi Et Liste Des Pièces De Rechange

FS125
Clean the machine, especially connections and
threaded unions, of any traces of oil, fuel or
preservatives before carrying out maintenance / repair.
Never use aggressive detergents. Use lint-free
cleaning rags.
Before cleaning the machine with water, steam jet or
detergents, cover or tape up all openings which -for
safety and functional reasons - must be protected
against water, steam or detergent penetration.
Do not clean the machine with a high-pressure
cleaner. The hard water jet can put damage to parts of
the machine. After cleaning, remove all covers and
tapes applied for that purpose.
After cleaning check
connections, chafe marks and damage! Have identified
defects repaired immediately!
Always tighten any screwed connections that have
been loosened during maintenance and repair.
Any safety devices removed for set-up, maintenance
or repair purposes must be refitted and checked
immediately upon completion of the maintenance and
repair work. Ensure that all consumables and replaced
parts are disposed of safely and with minimum
environmental impact.
2.7 Information about special risks
with electrical energy
Observe the relevant national regulations or standards.
Electrical connections must always be kept free from
dirt and moisture.
Use only original fuses with the specified rating! Switch
off the machine immediately, if trouble occurs in the
electric power supply!
If your machine comes into contact with a live wire:

warn others against approaching and touching the
machine

have the live wire de-energized
When working with the machine, maintain a safe
distance from overhead electric lines. If work is to be
carried out close to overhead lines, the working
equipment must be kept well away from them.
Caution, danger to life!

Check out the prescribed safety distances.

Work on the electrical system or equipment may
only be carried out by a skilled electrician himself
or by specially instructed personnel under the
control and supervision of such electrician and in
accordance with the applicable engineering rules.

If provided for in the regulations, the power supply
to parts of machines and plants, on which
inspection, maintenance and repair work is to be
carried out must be cut off.

Before starting work, check the de-energized
parts for the presence of power and ground or
short-circuit them in addition to insulating adjacent
live parts and elements.
the machine for loose
The electrical equipment of machines is to be
inspected and checked at regular intervals. Defects
such as loose connections or scorched cables must be
rectified immediately.
Necessary work on live parts and elements must be
carried out only in the presence of a second person
who can cut off the power supply in case of danger by
actuating the emergency shut-off or main power
switch. Secure the working area with a red-and white
safety chain and a warning sign. Use insulated tools
only.
If mobile electrical equipment, connecting cables and/
or extension/ appliance cords with plug connectors are
used, ensure that such equipment, cables and cords
are checked for correct function at least once every six
months by a qualified electrician or - if suitable testing
equipment is available - by a properly instructed
person.
Protective installations with fault-current protection
units used in non-stationary equipment must be
checked for correct operation at least once a month by
a properly instructed person.
Fault-current and fault-voltage protection units must be
checked for correct operation by actuating the testing
facility:

once on every working day in the case of mobile
equipment,

at least once every six months in the case of
stationary equipment.
2.8

Gas, dust, steam, smoke

Operate combustion engines only in well-ventilated
rooms! Before starting the unit in closed rooms, make
sure that the room is sufficiently ventilated and use the
exhaust gas hose!
Welding, burning and grinding operations on the
machine are only to be carried out if this is explicitly
authorized (there is the danger of fire and explosion)!
Before welding, burning and grinding operations clean
the machine and its surrounding area from dust and
flammable substances
ventilation (danger of explosion)!
When working in confined spaces observe any existing
national regulations!
2.9

Noise

During operation sound protection devices on the
machine must be in safe position. Wear the prescribed
personal ear protection! (UVV 29 § 10, Article 29 of
the Accident Prevention regulations).
The use of noise emitting machines may be restricted
to certain times by national or local regulations.
- 27-
and care for sufficient
5009002-00
BA-DE-GB-FR-NL (001)
®