Publicité
Les langues disponibles
Les langues disponibles
1.4.8 Bluetooth aktivieren/deaktivieren / (bLE)
bLE = Bluetooth = off / on
Only instrument with extension –B in the article number have got a Bluetooth
function. This function is described below.
To activate or deactivate bluetooth push (ENTER/MENUE). Use the up and
down keys (
) to select bLE. Push again (ENTER/MENUE). Use the up key
(
) to activate on or deactivate off the bluetooth function and push (ENTER/
MENUE) to confirm. Push (ESC) to revert back to the measuring mode.
Example of an activated Bluetooth function:
The arrow at the top right of the display shows you
that the Bluetooth function is activated. This setting
is deactivated when the device is switched off
(standard setting is bLE off).
Unit
Prob
L in 2
CAL
Note: When using the bLE function, the USB interface cannot be used
1.5 Recalling the memory data (HOLD MAX MIN AVE)
After pushing first time the key (HOLD MAX MIN AVE) the actual values will be
held on the display. Pushing again the key (HOLD MAX MIN AVE), the saved
maximum-, minimum and average values will be displayed.
Note: During the recall of the memory data the extremes (MAX MIN) and the
average value (AVE) will not be calculated or carried on.
Clearing the memory (MAX MIN AVE)
Press (CLEAR) key once to erase the stored maximum, minimum and average
from memory. On the display appears Clr. – After erasing the memory the
instrument automatically reverts back to measuring mode indicating the actual
measured value again.
1.6 Measuring rate (FAST-mode) only for temperature measurement
Press (FAST/ ) key once to change the measuring rate. Now the measuring
rate is app. 4 measurements per second. Press (FAST/ ) key again and the
instrument is back in the standard mode (1 measurement per sec.).
Note:
In the fast mode the battery consumption is three times higher than in the
standard mode.
Example:
The arrow at the top of the display indicates that the
FAST function is activated. This setting is deactivated
when the device is switched off.
1.7 AUTO-OFF-function
dAoF = Disable Auto-off
EAoF = Enable Auto-off
Press (ESC/AUTO-OFF) key once. On the display appears dAoF. Now the
Auto-Off-function is deactivated. Press (ESC/AUTO-OFF) key again. On the
display appears EAoF. Now the instrument switches off auto-matically after
app. 10 minutes.
32
MENUE
only -B
Geräte
ChnI
ArEA
Lo6
bLE
1.8 Special-functions
1.8.1 (Ohm//Micro volt/Volt/Hertz-display)
If you want to get the shown value displayed according to the basic units you will
have to push, when you switch on, the keys FAST and ON/OFF at the same time
for approximately 3 seconds till the next basic unit appears:
o = Ohm (Pt100)
H = Hertz (flow m/s)
u = Micro volt (thermocouples)
U = Volt (humidity)
°C
1.8.2 Zero adjustment
A long press on the F1 button (approx. 3 s) enables
you to set the displayed value on 0. Before pressing
the button make sure that the actual value also
amounts to 0 (no current/pressure at the probe). The
function is deactivated by pressing the F1 key again.
1.8.3 Deactivation of the 2nd channel (toggle)
A long press on the HOLD button (approx. 4 s) enables you to activate or
deactivate the 2nd measuring channel.
2. Power supply
- For the power supply of the instrument a 9 Volt dry battery is used.
To exchange the battery switch of the instrument and open the rear battery
cover. Remove the battery from the instrument and replace with a new battery.
- The "BAT" symbol in the display indicates that the battery needs to be
exchanged. After displaying the "BAT" symbol, the instrument allows
app. 1 hour of further operation.
- When using a rechargeable battery, the slide switch must set to "Akku" to
charge the battery by the USB interface. When using a standard battery
(non rechargeable) the slide switch must set to "Batt" to prevent any
damage to battery or instrument.
- Beside the 9 volt block battery the LOG-instruments disposes a
second battery (CR2032). This is the buffer battery for the
internal real time clock. The battery life time is appr. 4 years,
it doesn't matter whether the instrument has been used or not.
For the battery exchange the 4 screws of the housing
(rear side) has to be removed. Now the housing can be
opened. Now change the battery on the main board.
Afterwards remount the housing again. See picture below:
°C
Attention:
Please do not dispose of old electronic devices and empty batteries in household
waste. To protect the environment, take them to your retail store or to appropriate
collection sites according to national or local regulations.
°C
CR2032
33
Publicité
Chapitres
