Connections - Denon DRA-F100 Mode D'emploi

ENGLISH
4

CONNECTIONS

LD player, video deck, etc.
• Disconnect the ground cord if
humming or noise is produced
when it is connected.
NOTE:
This system includes digital circuitry which may
cause interference such as color blotching or
changes in the color on TVs. If this happens,
move the system and the TV as far apart as
possible.
AC Outlets
• SWITCHED outlet (DRA-F100)
The power of this outlet is switched on and off by the receiver's SYSTEM
power operation switch.
This outlet will also be switched on when the power is set to ON-
STANDBY with the remote control.
When the receiver is in the standby mode, the outlet switches off after
approximately 20 seconds.
• UNSWITCHED outlets (DCD-F100)
These outlets remains on at all times, regardless of the setting of the CD
player's and cassette's power operation switch.
Do not connect the receiver's AC cord to the outlets on the CD player
6
(DCD-F100). Doing so could result in damage.
All manuals and user guides at all-guides.com
FM
antenna
AM-FM Stereo Receiver
(DRA-F100)
SIGNAL GND
FM COAX 75º
L
R
PHONO AUX
Ground cord
Record player
LINE OUT
Use a record player with
an MM cartridge.
CD player
(DCD-F100)
Speaker systems
AM loop
antenna
Right
LOOP AM
ANT.
L
SYSTEM
CONNECTOR
1 2
R
R L
CD PB-TAPE-REC PB-MD-REC
IMPEDANCE 4~16º
SPEAKERS
OPTICAL
DIGITAL OUT
L
SYSTEM
CONNECTOR
1 2
R
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article
820-40 of the NEC which provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
System operations
Such system operations as the timer and the auto on functions,
as well as remote control operations cannot be performed
unless all the RCA pin-plug cords and system connector cords
are connected between the units, so be sure to make all the
connections properly as shown in the diagram. Also,
disconnecting system connectors while the system is operating
may result in malfunction. Be sure to unplug the power cord
before changing connections.
Connecting the speaker systems
Connect the speaker system for the
left channel (the left side as seen
from the front) to the "L" terminals,
the speaker system for the right
channel to the "R" terminals. Be sure
to use speaker systems with an
impedance of 4 Ω/ohms or greater.
Power plug
Left
AC 120 V 60 Hz
(Plug into a power outlet)
OPTICAL
AC OUTLET
120V 60Hz
R L R L
SWITCHED
120W(1A.)MAX
OUTPUT INPUT
AC OUTLET
120V 60Hz
UNSWITCHED
120W(1A.)MAX
R L R L
OUTPUT INPUT
• Do not plug the power cord in
• Insert the plugs securely. Inco
• Be sure to connect the speake
• After unplugging the power co
• Note that setting the connecti
Whenever
in the STAN
unit is still
voltage.
Please be s
cord when
say, a vaca
PERSONAL COMPONENT SYSTEM / MINID
B
POWER LOADING MEC
REMOTE SENSOR
EJECT
PICK REC MODE
INPUT SELECT
ON / STANDBY
DIGITAL ANALOG
D.IN 1 L
dB -60
R
04Tr 12
1 2 RANDOM
Connecting a
Connections for
Connect the tape
(OUT) jacks using
Connections for
Connect the tape
(IN) jacks using pi
PERSONAL COMPONENT SYSTEM / STEREO
B
OPEN / CLOSE
REV. MODE
ON / STANDBY
dB -40 -30 -20
L
R
TAPE B
Connecting a
Connections for
Connect the tape
(REC) jacks using
Connections for
Connect the tape
(PB) jacks using p
sure to interconnect the chann
diagram.
systems with the same polarit
the center will be weak, the p
stereo effect will be lost.
in humming or other noise.