Product Description And Specifications - Bosch PSA 900 E Notice Originale

OBJ_BUCH-1352-004.book Page 11 Friday, June 27, 2014 12:39 PM
 Clamp material well. Do not support the workpiece
with your hand or foot. Do not touch objects or the floor
with the the saw running. Danger of kickback.
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than by
hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual cur-
rent device (RCD) with a rated residual current of 30 mA
or less.
Product Description and
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for sawing wood, plastic, metal and
building materials while resting firmly on the workpiece. It is
suitable for straight and curved cuts. When using the appro-
priate bimetal saw blades, it is possible to cut flush to the
workpiece surface. The saw blade recommendations must be
observed.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Saw blade*
2 Base plate
3 Saw blade holder
4 Stroke rod
5 SDS clamping lever for saw blade release
Bosch Power Tools
6 On/Off switch
7 Handle (insulated gripping surface)
8 Clamping plate
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Sabre saw
Article number
Rated power input
Stroke rate at no load n
0
Tool holder
Stroke rate control
Stroke
Cutting depth, max.
– in wood
– in non-alloy steel
– pipe diameter
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-11.
Typically the A-weighted noise levels of the product are:
Sound pressure level 90 dB(A); Sound power level
101 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting board: a =20 m/s , K=1.5 m/s
h
Cutting wooden beam: a =32 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for differ-
ent applications, with different accessories or insertion tools
or is poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over the
total working period.
An estimation of the level of exposure to vibration should al-
so take into account the times when the tool is switched off
or when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of work
patterns.
English | 11
PSA 900 E
PSA 9000 E
3 603 CA6 0..
W 900
-1
min 0–2700
SDS

mm 28
mm 200
mm 20
mm 150
kg 3.5
/II
2
,
2 2
, K=1.5 m/s .
1 609 92A 0RC | (27.6.14)