Re-Assigning Device Keys; Operating Other Components - Kenwood KRF-V6070D Mode D'emploi

Basic remote control operations for other components

Re-assigning device keys

The remote control can be set up to control a second TV or VCR, or any
combination of eight home entertainment components.
For example, to control the operation of two different VCR using the
remote control, the user need to re-assign the unused VID2 key to
operate the second VCR (VID1) as follows:
1
Press and hold the Remote Setup key until the LED blinks
twice, then release the Remote Setup key.
2
Press the numeric key to enter "9 - 9 - 2".
• The LED will blink twice.
3
Press the VID1 key once, then press the VID2 key once.
•The user now can operate VID2 as a second VCR along with VID1.
• Refer to the table in the previous page for the combination of
source keys and the other components assignment.
4 To re-assign other device keys, repeat steps 1 through 3 by
substituting the key sequence from the chart below for the
most popular components:
To re-assign key
Sequence
TV as 2nd VID1 key
TV as 2nd VID2 key
TV as 2nd CD/DVD key
TV back to TV key
VID1 as 2nd TV key
VID1 as 2nd VID2 key
VID1 as 2nd CD/DVD key
VID1 back to VID1 key
5
To clear the re-assignment and reset the remote control to its
original operation mode:
1 Press and hold the Remote Setup key until the LED blinks
twice, then release the Remote Setup key.
2 Press the numeric key to enter "9 - 9 - 2".
3 Press the VID2 key twice.
• When a re-assignment is done, the LED will blink twice to confirm
your choice. At that time, you will need to program the remote
control in order to control the new component.
• If an invalid key sequence is entered, the LED blink once and return
to normal operation.
• When in Tuner mode, re-assignment is not available.
30 EN
Perform
Remote Setup -9 -9 -2 -VID1 - TV
Remote Setup -9 -9 -2 -VID2 - TV
Remote Setup -9 -9 -2 -CD/DVD - TV
Remote Setup -9 -9 -2 -TV - TV
Remote Setup -9 -9 -2 -TV - VID1
Remote Setup -9 -9 -2 -VID2 - VID1
Remote Setup -9 -9 -2 -CD/DVD - VID1
Remote Setup -9 -9 -2 -VID1 - VID1

Operating other components

This operation lets you operate the registered components.
KENWOOD audio components with system control turn on and off
automatically with the receiver via the system control connections.
SRC Power
ª
1
Use the Source keys to select the component you desire.
• Pressing the Source keys also changes the input selector on the
receiver.
• When you operate your registered DVD player, CD player, Cassette
deck, MD player, Cable, DTV decoders, VCR or TV, go to step 2.
• When you operate the CD player, Cassette deck, MD player, or
Tuner with system control connection, go to step 3.
2
Press the SRC (source) Power key.
• To return to the receiver operation mode, press the TUNER key for
more than 3 seconds.
3
Press the operation keys you desire.
The remote control mode remains at the selected input. If you
wish to operate another component, repeat step 2 or 3.
Note
• Be sure to point the remote control at the remote sensor on the
receiver when you want to operate KENWOOD components
connected by system control cords. Otherwise, point the remote
control at the component you want to operate.
• To initialize the remote control, press the Remote Setup key until
the LED blinks twice. Then press the numeric key to enter "9-8-1".
The LED blinks twice.
Source
keys
+ +
¢
4
+
7
fi