Ribind MASTER Wi-Fi Mode D'emploi page 24

G
B
- At this time pressing one of the buttons on the transmitter will memorize the code.
Successful code memorization is shown by the dual-color LED DL7 emitting a green light
for 500ms and by a sound from the buzzer, indicating successful memorization.
- After memorizing the first code, the memorization time resets for 10 seconds and it is
possible to memorize more codes.
To finish the code memorization procedure, allow 10 seconds to pass until the flashing red
LED DL7 turns off. Alternatively, push button PROG RX on the MASTER Wi-Fi, also in this
case the flashing red LED DL7 turns off, indicating the end of the memorization procedure.
With the dual-color DL7 off, the MASTER Wi-Fi is ready to work.
- Push a button of a previously memorized remote control. The green LED DL7 on the
MASTER Wi-Fi comes on for a moment, indicating recognition of a valid code. After 2
second led DL5 comes on for a moment, at the same time, total opening is ordered.
Note: If, when pushing a button on the remote control, the dual-color LED DL7 turns red for
a moment, this means that the code is not in the memory and you must therefore perform
the memorization procedure again.
P
ROGRAMMING REMOTE CONTROLS FOR PEDESTRIAN OPENING
(maximum of 100 codes)
If the MASTER Wi-Fi memory is empty (standard version), the dual-color LED DL7 flashes
alternately red and green.
In addition to the codes, MASTER Wi-Fi also learns the channels that are desired
for use. Be careful to remember the buttons pushed on the remote controls during
the code memorization procedure as they will be those used thereafter for the
total opening.
If no code is sent, after 10 seconds the green dual-color LED DL7 on the MASTER Wi-Fi
turns off indicating the end of the programming procedure. The dual-color LED DL7 flashes
alternately red and green indicating that there are no codes in the memory.
- Push and hold the button PROG RX for at least 3 seconds. Upon release the dual-color LED
DL7 on the edge of the MASTER Wi-Fi turns red.
- Push the button PROG RX on the MASTER Wi-Fi again. The flashing red LED DL7
begins flashing green for 10 seconds, indicating that the codes to be memorized will
be associated with pedestrian control. At this time, pushing one of the buttons on the
transmitter (different from that used for total opening) will memorize the code. Successful
code memorization is shown by the dual-color LED DL7 emitting a red light for 500ms and
by a sound from the buzzer, indicating successful memorization.
- After memorizing the first code/remote control, the memorization time resets for 10
seconds and it is possible to memorize more codes/remote controls.
- To finish the code memorization procedure, allow 10 seconds to pass until the flashing
green LED DL7 turns off. Alternatively, push button PROG RX on the MASTER Wi-Fi, also
in this case the flashing green LED DL7 turns off, indicating the end of the memorization
procedure.
With the dual-color DL7 off, the MASTER Wi-Fi is ready to work.
- Push a button of a previously memorized remote control. The green LED DL7 on the
MASTER Wi-Fi comes on for a moment, indicating recognition of a valid code.
After 2 second led DL5 comes on for a moment, at the same time, total opening is ordered.
Note: If, when pushing a button on the remote control, the dual-color LED DL7 turns red for
a moment, this means that the button/code is not in the memory and you must therefore
perform the memorization procedure again.
T
OTAL CODE REMOVAL PROCEDURE
- Position jumper JP2 as shown here:
- Push and release button PROG RX on the MASTER Wi-Fi. The dual-color LED DL7 emits
a red light for 0.5 sec. and then turns off, indicating successful removal of codes and
start-up information..
- Position jumper JP2 as shown here:
- The LED DL7 begins flashing alternately red and green, indicating that the memory is
empty.
Note: Jumper JP2 during normal operation must be positioned as shown here:
F
ULL MEMORY SIGNAL
If, when pushing and holding button PROG RX on the MASTER Wi-Fi for at least 3 seconds,
upon release the dual-color LED DL7 flashes green 6 times, this means that the memory is
full (maximum 100 codes).
To download the video of the installation write the following
address in your browser, or, read the QR code with your
smartphone:
http://www.youtube.com/user/RIBSRL?feature=mhee
24
24