Ribind MASTER Wi-Fi Mode D'emploi page 18

G
B
SUN CLONE 2CH
Code ACG6056
SUN CLONE 4CH
Code ACG6058
NOVA Wi-Fi
Code ACG8037
VERTIGO Wi-Fi 8
Code ACG8042
VERTIGO Wi-Fi 10
Code ACG8043
The Wi-Fi System complies with the standard EN13849-2:2008 and together with
a RIB electronic control panel is a Class 2 protection device.
The Wi-Fi System through the use of the MASTER Wi-Fi card permits the
construction of a system with NOVA Wi-Fi photocells and TOUCH Wi-Fi strips
which also attach to the moveable panel without the need for a cable collector.
The system constantly monitors the presence of the various safety devices and the status
of the batteries, completely meeting the need for active safety for all types of openings.
Using the RIB electronic control panel it is possible for the system to perform an auto test
as required by current standards.
Each radio-controlled safety device has its own internal identification code which
distinguishes it from the others.
R
EFERENCE STANDARDS FOR AUTOMATIC DOORS AND GATES
The installer must ensure that the Wi-Fi System is connected as specified by the standard
EN12453 as per 5.1.1.6 (points e and f) to an electronic control panel capable of performing
an operations check before closing (AUTO TEST).
Therefore, the use of RIB devices permits system installation in compliance with current
Standards and Directives.
Once machine installation is complete it must be ascertained that it complies with standard
EN13241-1.
RIB may not be held responsible for any damage caused by improper, wrong or unreasonable
use of the product.
M
ASTER Wi-Fi
This is the heart of the system: it runs all of the control (433,92 MHz), safety and signaling
(868,3 MHz) devices programmed in the installation phase.
MASTER Wi-Fi is available in 4 versions:
- MASTER Wi-Fi with connection couplings (code ACG6094), for use with all non-CRX
RIB electronic control panels.
- MASTER Wi-Fi with terminal block (code ACG6099), for use with other brands or RIB
CRX panels.
- MASTER Wi-Fi FR with terminal block (code ACG6150), for use with other brands or
RIB CRX panels.
- MASTER Wi-Fi OS with terminal block (code ACG6152), for use with other brands or
RIB CRX panels.
SUN 2CH
Code ACG6052
SUN 4CH
Code ACG6054
TOUCH Wi-Fi
Code ACG3016 Code ACG6202
S
AFETY DEVICES
MASTER Wi-Fi can operate up to 6 safety devices (NOVA Wi-Fi + VERTIGO Wi-Fi + TOUCH
Wi-Fi + TX RED) at the same time.
- NOVA Wi-Fi photocells (code ACG8037): can be connected to a TOUCH mechanical strip
(code ACG3015) or a resistive strip on both the photocell transmitter and the photocell
receiver.
- VERTIGO Wi-Fi photocells (VERTIGO Wi-Fi 8 code ACG8042 - VERTIGO Wi-Fi 10 code
ACG8043): wireless vertical photocells substituting the sensitive edge.
- TOUCH Wi-Fi strip (code ACG3016), with built-in transmitter/receiver.
- TX RED (code ACG6202): radio transmitter to manage mechanical or resistive safety
strips.
C
ONTROLS
MASTER Wi-Fi runs up to 100 different remote control codes:
- SUN dual-channel 433,92 MHz remote controls (code ACG6052)
- SUN four-channel 433,92 MHz remote controls (code ACG6054)
- SUN CLONE dual-channel 433,92 MHz remote controls (code ACG6056)
- SUN CLONE four-channel 433,92 MHz remote controls (code ACG6058)
- BLOCK Wi-Fi mono-channel 433,92 MHz key selector switch (code ACG6098).
It is also possible to connect a wired controls with N.O. contact (key selectors, push-
buttons...).
V
ISUAL SIGNALS
MASTER Wi-Fi can operate one or more SPARK Wi-Fi Blinkers (868,3 MHz) code
ACG7064.
MASTER Wi-Fi has LEDs for monitoring system status and for identifying photocells or strips
with low or exhausted batteries.
S
OUND SIGNALS
MASTER Wi-Fi has a buzzer which signals installation phases and a warning if the batteries
are low or exhausted or, acts as an alarm in case one of the devices is not functioning.
18 18
18 18
RADIO NUMERIC CODER
Code ACG9434 embedd
Code ACG9436 to wall
TX RED
BLOCK Wi-Fi
Code ACG6098
SPARK Wi-Fi
Code ACG7064
TOUCH
Code ACG3015
or other brands
mechanical/resistive
strip