Ribind MASTER Wi-Fi Mode D'emploi page 20

G
B
C
- LAYOUT
J8
J1
BUZZER
J1 => CONNECTOR FOR CONNECTIONS TO THE CONTROL PANEL AND SAFETY AND
CONTROL INPUTS
Green wire => pedestrian control PED
Gray wire => contact common COM
Yellow wire => sensor EDGE
Black wire => photocell PHOT N.C.
White wire => terminal for connecting the wire coming from the system control
button N.O.
Brown wire => auto test power feed A-D+ TEST.
J2 => CONNECTOR FOR CONNECTIONS TO THE 12/24V ac/dc CONTROL PANEL
AT THE BLINKER OUTPUT (CHECK POLARITY)
Red wire => positive (connects to the positive pole of the blinker output)
Black wire => negative (connects to the negative pole of the blinker output)
J4 => TERMINALS FOR CONNECTIONS TO THE 120/230V CONTROL PANEL, AT
THE BLINKER OUTPUT
J5 => FEMALE CONNECTOR FOR CONNECTION TO NOT CRX RIB CONTROL PANELS
(MASTER Wi-Fi code ACG6094) OR TERMINAL BOARD FOR CONNECTIONS TO
OTHER BRANDS OR RIB CRX CONTROL PANELS (MASTER Wi-Fi code ACG6099)
J8 =>
TERMINAL FOR CONNECTION TO THE ANTENNA 868,3 MHz
JP1 => A/D+ TEST see SELF-TEST-ENABLED RIB ELECTRONIC BOARD CHART.
- Jumper selection AUTOTEST mode for other brands control panels with AUTOTEST
negative power feed
+/~ Jumper selection AUTOTEST mode for control panels with AUTOTEST positive/
alternate power feed (as RIB control panels)
JP2 => Radio-control code removal for total and pedestrian opening
S1
10 9 6 5 2 1
+ -
MASTER Wi-Fi code ACG6094
1 central antenna 433
2 ground-plane antenna
3-4 open
5 negative power feed 12/24V ac/dc
6 positive power feed 12/24V ac/dc
7-8 feed
9-10
total open/close control
SW1 JP1
10 9 6 5 4 3 2 1 6 5 2 1
J5
+ - + -
MASTER Wi-Fi with terminal block code ACG6099
1 central antenna 433
2 ground-plane antenna
3 negative power feed 12/24V ac/dc
4 positive power feed 12/24V ac/dc
5-6 connects to the control panel at the total open/close control input
button (K BUTTON for RIB panels)
SW1 => Micro-switches for pairing and identifying strips and photocells
S1 => PROG. RX Programming button
BUZZER =>
Sound signal for installation, warning and alarm status
LED
DL1 (red) - pedestrian opening control N.O. (PED)
DL2 (red) - strip contact N.C. (EDGE)
DL3 (red) - photocell contact N.C. (PHOTO)
DL4 (red) - total opening command with push-button N.O. in the system
DL5 (green) - activated total opening radio-control.
DL6 (yellow) - electrical power indicator 12-24V ac/dc
DL7 (dual-color) - radio code learning for total, pedestrian and blinker opening
DUAL-COLOR LED EDGE PHOT
off => operating normally
green => strip sensor or photocell engaged
red/green => alarm
LED EDGE PHOT 1 - EDGE SENSOR OR PHOTOCELL 1
LED EDGE PHOT 2 - EDGE SENSOR OR PHOTOCELL 2
LED EDGE PHOT 3 - EDGE SENSOR OR PHOTOCELL 3
LED EDGE PHOT 4 - EDGE SENSOR OR PHOTOCELL 4
LED EDGE PHOT 5 - EDGE SENSOR OR PHOTOCELL 5
LED EDGE PHOT 6 - EDGE SENSOR OR PHOTOCELL 6
SW1 MICRO-SWITCHES - DIP
DIP 1 ON => STRIP SENSOR OR PHOTOCELL 1 ACTIVATED
DIP 2 ON => STRIP SENSOR OR PHOTOCELL 2 ACTIVATED
DIP 3 ON => STRIP SENSOR OR PHOTOCELL 3 ACTIVATED
DIP 4 ON => STRIP SENSOR OR PHOTOCELL 4 ACTIVATED
DIP 5 ON => STRIP SENSOR OR PHOTOCELL 5 ACTIVATED
DIP 6 ON => STRIP SENSOR OR PHOTOCELL 6 ACTIVATED
ATTENTION: every time is executed a change of position of dip switches, press PROG
RX push-botton for 6 times to update the system programming.
At the end the dual-color leds EDGE/PHOT must be turn off.
20 20
20 20
Dual-color Led
JP2
EDGE PHOT 1-6
12/24V ac/dc
6 5 4 3 2 1
+ -
J4
J2