Operation; Cleaning, Maintenance And Ordering Of Spare Parts; Carbon Brushes; Ordering Replacement Parts - Gardol GAH-E 2046 Li Mode D'emploi D'origine

6. Operation

Switching ON/OFF.
The hedge trimmer is equipped with a two-han-
ded safety switch. The machine works only when
the switch on the steady grip (Figure 1 / Item 3)
is pressed with one hand and the switch on the
handle (Figure 1 / Item 4) is pressed with the
other hand. If either switch is released, the cutters
will stop moving. Please watch out for the cutters
as they slow down to a standstill.
Notes on working practice
•
A hedge trimmer can be used to cut shrubs
and bushes as well as hedges.
•
To obtain the best cutting results, hold the
hedge trimmer so that the cutter teeth are
at an angle of approx. 15° in relation to the
hedge (see Figure 7).
•
The twin-bladed cutters rotate in opposite
directions, thus enabling cutting in both direc-
tions (see Figure 8).
•
It is recommended to tie a guide line of string
or the like along the hedge so that you cut the
hedge to a level height. Cut off all branches
which protrude beyond the guide line (see
Figure 9).
•
Cut the sides of the hedge with curve-shaped
movements from the bottom up (see Figure
10).
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Turn off and remove the rechargeable battery
from the hedge trimmer, before putting down or
cleaning.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
Anl_GAH_E_E_2046_Li_SPK7.indb 17 Anl_GAH_E_E_2046_Li_SPK7.indb 17
GB
ingress of water into an electric tool increases
the risk of an electric shock.
•
Remove deposits from the guard hood with a
brush.

7.2 Carbon brushes

In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be
replaced by anyone but a qualifi ed electrician.
7.3 Maintenance
•
The cutters should be cleaned and lubricated
at regular intervals in order to ensure best
performance at all times. Remove deposits
with a brush and apply a thin film of oil (Figure
11).
•
There are no parts inside the equipment
which require additional maintenance.
•
For storage, the hedge trimmer can be hung
up on a nail, screw or similar in a borehole on
the impact guard, with blade guard mounted
(Fig. 12)

7.4 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
- 17 -
10.12.14 13:54 10.12.14 13:54