Functional Description - Makita DUB184 Manuel D'instructions

ASSEMBLY
CAUTION:
Always be sure that the machine is
switched off and the battery cartridge is removed
before carrying out any work on the machine.
Installing the front nozzle
1. Loosen 2 screws with the hex wrench, and then
pull the screws all the way.
► Fig.1: 1. Screw
2. Make sure that the Makita logo on the front nozzle
is facing the direction shown in the figure, and then
attach the front nozzle to the machine.
► Fig.2: 1. Front nozzle
3. Tighten the screws with the hex wrench.
► Fig.3: 1. Screw
Installing the flat nozzle or
extension nozzle
Optional accessory
1.
Attach the adapter pipe to the front nozzle, and
then turn it clockwise to lock it into place.
► Fig.4: 1. Adapter pipe 2. Front nozzle
2. Attach the flat nozzle or extension nozzle to the
adapter pipe, and then turn it to lock it into place.
► Fig.5: 1. Flat nozzle 2. Extension nozzle 3. Adapter
pipe
Installing the gutter nozzle
Optional accessory
The gutter nozzle can be installed on the blower. The
adapter pipe designed exclusively for this model is
required to install the gutter nozzle.
For more details, refer to the instruction manual pro-
vided with the gutter nozzle.
Attaching the shoulder strap
Optional accessory
CAUTION:
Be sure to attach the hooks of
the shoulder strap to the machine securely. If the
hooks are attached incompletely, they may come off
and cause an injury.
CAUTION:
Be sure to use the shoulder strap
dedicated to this machine. Using other shoulder
strap may cause an injury.
CAUTION:
When you use the machine in com-
bination of the backpack-type power supply such
as portable power pack, do not use the shoulder
strap included in the machine package.
If you put on the shoulder strap included in the
machine package and the shoulder harness of the
backpack-type power supply at the same time,
removing the machine or backpack-type power sup-
ply is difficult in case of an emergency, and it may
cause an accident or injury.
Attach the hooks of the shoulder strap to the machine
as shown in the figure.
► Fig.6: 1. Hook
You can also attach the shoulder strap to the machine
as shown in the figure by attaching one end of the
shoulder strap to the buckle of the shoulder strap.
► Fig.7: 1. Buckle
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the machine is
switched off and the battery cartridge is removed
before adjusting or checking function on the
machine.
Installing or removing battery
cartridge
CAUTION:
Always switch off the machine
before installing or removing of the battery
cartridge.
CAUTION:
Hold the machine and the battery
cartridge firmly when installing or removing bat-
tery cartridge. Failure to hold the machine and the
battery cartridge firmly may cause them to slip off
your hands and result in damage to the machine and
battery cartridge and a personal injury.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the machine, causing
injury to you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
► Fig.8: 1. Red indicator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the
machine while sliding the button on the front of the
cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
► Fig.9: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
8 ENGLISH