Optional Accessories - Makita DGD800 Manuel D'instructions

Replacing carbon brushes
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes. (Fig. 9)
Insert the top end of slotted bit screwdriver into the notch
in the tool and remove the holder cap cover by lifting it
up. (Fig. 10)
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps. (Fig. 11)
Reinstall the holder cap cover on the tool.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Side handle (accessory) (Fig. 12, 13, 14 & 15)
When using the side handle, remove the rubber protec-
tor, insert the side handle on the tool barrel as far as it
will go and rotate it to the desired angle. Then tighten the
handle firmly by turning clockwise.
CAUTION:
• When using the tool without handle, always install the
rubber protector on the tool.
• When installing the rubber protector, always push it
onto the tool so that the top round recessed shape of
the rubber is positioned near the switch position.
• Wheel points
• Collet cone (3 mm, 6 mm, 8 mm, 1/4", 1/8")
• Collet nut
• Wrench 13
• Side handle set
• Makita genuine battery and charger
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
8
ENG905-1
): 72 dB (A)
pA
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Model DGD800
Work mode: surface grinding
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model DGD801
Work mode: surface grinding
Vibration emission (a
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been mea-
sured in accordance with the standard test method and
may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the oper-
ator that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Cordless Die Grinder
Model No./ Type: DGD800, DGD801
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN60745
The technical file in accordance with 2006/42/EC is avail-
able from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
10.11.2015
Yasushi Fukaya
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
2
): 6.5 m/s
h, SG
2
2
): 2.5 m/s or less
h, SG
2
Director
ENG900-1
ENG901-1
ENH101-18