Functional Description - Makita MP100D Manuel D'instructions

FUNCTIONAL
DESCRIPTION
Always be sure that the tool is
CAUTION:
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery cartridge
Always switch off the tool before
CAUTION:
installing or removing of the battery cartridge.
Hold the tool and the battery car-
CAUTION:
tridge firmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
► Fig.1: 1. Red indicator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
Always install the battery cartridge
CAUTION:
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
Do not install the battery cartridge
CAUTION:
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
► Fig.2: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
Indicator lamps
Lighted
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Remaining
capacity
Off
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Battery protection system
The tool is equipped with a battery protection system.
This system automatically cuts off power to the motor to
extend battery life.
The tool will automatically stop during operation if the
tool and/or battery are placed under one of the following
conditions:
Overloaded:
The tool is operated in a manner that causes it to draw
an abnormally high current.
In this situation, turn the tool off and stop the application
that caused the tool to become overloaded. Then turn
the tool on to restart.
If the tool does not start, the battery is overheated. In
this situation, let the battery cool before turning the tool
on again.
Low battery voltage:
The remaining battery capacity is too low and the tool
will not operate. If you turn the tool on, the motor runs
again but stops soon. In this situation, remove and
recharge the battery.
Main power switch
Always turn off the main power
WARNING:
switch when not in use.
When carrying the tool, turn off the
CAUTION:
main power switch. Otherwise, pulling the switch
trigger unintentionally may cause an injury.
► Fig.3: 1. Main power switch
To turn on the tool, press the main power switch. To turn
off the tool, press the main power switch again.
NOTE: This tool employs the auto power-off function.
To avoid unintentional start up, the main power switch
will automatically shut down when the switch trigger
is not pulled for a certain period after the main power
switch is turned on.
Switch action
Before installing the battery car-
WARNING:
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
► Fig.4: 1. Switch trigger
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
Pressure gauge
► Fig.5: 1. Unit button 2. Minus button 3. Plus button
If the object to be inflated is connected to the tool, the
air pressure of the object is displayed on the pressure
gauge when you turn on the tool. If nothing is connected
to the tool, the pressure gauge displays "0".
You can set the air pressure on the pressure gauge. To
change the unit, press the unit button. To increase the
pressure value, press the plus button. To decrease the
pressure value, press the minus button. You can set the
pressure value between 20 kPa and 830 kPa.
8 ENGLISH