Publicité
schieber muss ganz eingeschoben sein, damit die offene Flamme das Handrad am
Wasserablassventil nicht beschädigt. Wichtig: Nach Beendigung des Heizens den
Brennerschieber, während er noch warm ist, also vor dem Abkühlen/Erkalten
aus der Führung herausnehmen. Sonst kann sich der Schieber durch das Verkleben
von Brennrückständen festklemmen. Sollte der Brennerschieber einmal festsitzen,
kann man diesen dann durch ein leichtes Verkanten nach links/rechts lösen.
Achtung: Die Befeuerung mit Trockenbrennstofftabletten erfordert viel
Sauerstoff. Eine gute Belüftung des Zimmers ist daher notwendig!
Tabletten, die nicht restlos abgebrannt sind, wegen der auftretenden Ge-
ruchsbelästigung nicht ausblasen, sondern unbedingt ausbrennen lassen.
Falls nicht genügend Wasser im Kessel ist, sollte der Brennerschieber auf
eine feuerfesten Unterlage gelegt werden und hier die Brennstofftabletten
restlos abbrennen lassen.
17. Das Dampfabsperrventil bei sichtbarer Dampfentwicklung (Manometerstand ca. 1
bar) durch eine Drehung nach links öffnen. Das Schwungrad von Hand anwerfen, da-
mit das in der Dampfleitung und dem Zylinder befindliche Kondenswasser entwei-
chen kann. Dadurch setzt sich die Dampfmaschine in Betrieb. Die Drehzahl des
Schwungrades kann durch das Dampfabsperrventil geregelt werden.
18. Der Kondenswasserbehälter sollte während des Dampfbetriebes mehrfach entleert
werden. Hierzu vorher das Dampfabsperrventil schließen und die Dampfmaschine
stoppen.
19. Mit der Speisewasserpumpe kann während des Betriebes der Dampfmaschine
Wasser in den Kessel nachgefüllt werden. In das Vorratsbecken, unter der Pumpe,
Wasser einfüllen und dann durch das Betätigen des Pumpenhebels das Wasser in den
Kessel pumpen. Achtung: Falls zu viel kaltes Wasser in den Kessel gepumpt wird,
baut sich der Dampfdruck ab. Nach Beendigung des Dampfbetriebes kann das Rest-
wasser aus dem Vorratsbecken in den Kessel gepumpt werden und dieser über das
Wasserablassventil geleert werden.
20. Nach Beendigung des Dampfbetriebes und dem Abkühlen sollte die Dampfma-
schine gewartet werden. Noch im Kessel vorhandenes Wasser durch das Öffnen des
Wasserablassventils entleeren. Hierzu das Wasserablassventil öffnen und die Dampf-
pfeife durch leichtes Ziehen an der Kette öffnen - so entsteht kein Unterdruck beim
Entleeren des Restwassers. Vorsicht bei heißem Wasser! Im Kessel verbleibendes
Wasser kann der Funktion nicht schaden, aber evtl. zu Ablagerungen an dem Schau-
glas führen. Kalkrückstände am Wasserstandsschauglas oder im Kessel auf keinen
Fall mit Essig oder sonstigen stark ätzenden Mitteln entfernen (Empfehlung: Ver-
wendung eines kalklösenden Mittels, welches Messing und Lötzinn nicht angreift).
Eine Rußbildung an der Unterseite des Kessels beeinflusst ebenfalls nicht die Funk-
tion und kann mit einer Bürste entfernt werden. Zum Abschluss das Modell trocken-
putzen.
Garantie:
21. Alle WILESCO-Dampfmodelle durchlaufen eine Endkontrolle. Bei einem evt.
Fehler können Sie die Dampfmaschine über Ihren Fachhändler oder direkt an uns ein-
senden. Wir bitten um Verständnis, dass bereits angeheizte/gebrauchte Modelle nicht
gegen neue ausgetauscht werden können. Die häufigsten Reklamationen sind undich-
te Dampfkessel. Die Lötnaht wird durch Beheizung ohne ausreichenden Wasserstand
zerstört. In solchen Fällen verflüssigt sich das Lötzinn an der Lötnaht tropfenförmig
und der Kessel wird undicht. Dies ist ein eindeutiger Beweis, daß der Kessel trocken-
beheizt wurde. Bitte beobachten Sie stets sorgfältig den Wasserstand, da eine Tro-
ckenbeheizung jegliche Garantieansprüche ausschließt.
Umweltschutz wird auch bei uns groß geschrieben. Somit haben Sie die Möglichkeit
nach einem langen Dampfmaschinenleben diese und auch die Original-Verpackung
an uns zurückzugeben. (Versandkosten werden nicht übernommen.) Alle zurückge-
sandten Modelle / Verpackungen werden von uns einem fachgerechten Recycling zu-
geführt.
Dieses Modell ist ausschließlich für die oben beschriebene Funktion bestimmt.
Technische Änderungen behalten wir uns vor.
WILESCO wünscht Ihnen nun viel Spaß mit Ihrer Dampfmaschine und Volldampf
voraus !
Attention! Before operating this steam engine model please
read and observe thoroughly the operation instructions.
Important information and safety precautions for your own
safety:
1. For safety reasons, children should run the steam
engine only under supervision of adults (recommended
age: from 8 years on, not recommended for children
under 36 months). During the operation of the steam
model until its complete cooling the engine must be under
constant observation.
2. Each irregularity during operation has to be repaired by a competent and
authorized person or by WILESCO themselves. Otherwise any warranty expires.
3. Any unauthorized change, repair or manipulation to the standard specification will
also invalidate the warranty.
4. All parts which are under steam pressure so as boiler, spring loaded safety valve
etc. leave our works only after a 100% examination. The spring loaded safety valve
must not be manipulated. The operation of the steam engine without any spring
loaded safety valve is not allowed The function of the spring loaded valve has to be
checked before each operation by pressing the spring or by a small pull on the upper
valve rod. If lime residues caused by hard water are visible on the spring loaded
safety valve, it has to be replaced immediately.
5. High temperatures: The principles on which the engine works mean that the
burner slide, boiler, boiler house, the spring loaded safety valve, the steam pipes etc.
become very hot. Do not touch in order to avoid the risk of burns.
6. Safety precautions: During operation, take care that children do not touch any of
the moving parts.
7. Danger if the boiler is heated without enough water! Always
ensure that there is enough water in the boiler of the steam engine.
Caution: When refilling WiTabs dry fuel tablets also refill up to the
max. level.. The water must always be visible at least at the lower
end of the sight glass, otherwise the joints become leaking and the
boiler will be destroyed. Any resulting claim, damage or consequential
damage cannot be accepted. If the boiler or any steam leading part leak, stop the
steam model immediately by removing the burner slide. Any necessary repair should
be carried out by authorized staff or at the WILESCO company.
8. The steam engine meets all safety standards and actual regulations. Each boiler has
been submitted to a bursting pressure and water test of 5 bar. The operating pressure
is maximally 1,5 bar.
9. Imperatively keep the operating instructions with your steam engine.
10. We advise you to place the stationary steam engine on a non sliding surface or fix
it onto a coated chipboard (approx. 16 mm thick) with 4 woodscrews (3,4 x 45 mm).
The size of the board depends on how many models will be run with the steam
engine.
Caution: Don't operate the steam model near flammable objects or on temperature-
sensitive surfaces. Operation only under windless condition.
Operating instructions
11. Firstly screw the spring-loaded safety valve with washer from the above block of
the pressure gauge. The small pressure gauge has to be screwed-in at the side and to
be adjusted by using washers. Then, after filling with water screw the component part
into the opening of the boiler provided for it. The pressure gauge points forward to
the watergauge glass. This can be adjusted with washers of different thickness.
12. Unscrew the whole base, including pressure gauge and spring-loaded safety valve, (or
alternatively the steam whistle) and fill the boiler with the funnel approx. 3/4 full
(upper edge of the water gauge glass), if possible with warm water. Lift the funnel
slightly so that the air inside the boiler can escape. Use only deficient in lime water
or, even better, water without any lime (e.g. distilled water). Then refit the whole
base.
13. Screw the steam whistle onto the boiler. Do use only the spanner provided with
the Engine. Do not tighten by turning the lever as this will be damaged. When
screwing in the steam whistle, the lever with the chain should point outwards (use
washers if necessary) so that the chain which operates the whistle does not come in
contact with the boiler. Pull the chain gently to operate the whistle. Note: The steam
whistle allows to regulate easily any overpressure in the boiler. Assemble the
smoke stack with the enclosed screws on the back side of the boiler house.
14. Before you oil the cylinder, turn off the steam supply valve. Then turn off the
oil filler screw and fill in with WILESCO steam oil (item n° Z 83) while turning the
flywheel several times so that the oil is grawn in. Oil again when you refill dry spirit
tablets so that the piston does not seize (2-3 drops of oil are sufficient for an
operating time of abt. 10 minutes). Keep the steam supply valve closed during the
oiling procedure. No steam pressure must be in the boiler. Oil lightly all of the
bearings and linkages. Before refilling the boiler with water, check by operating the
steam whistle that no steam pressure is in the boiler.
15. Do not push in the condensation tray untilsteam is visible, otherwise the tray
could becomedeformed due to the high heat effect.
16. Place 3 WiTabs dry fuel tablets upright into the burner slide (not
more than 3 pcs.) and light them. Use only the original WILESCO
burner slide. Caution: because of the risk of danger from an open
flame, always take the necessary safety precautions. The burner slide
is adjustable. The oxygen supply and the flame height can be adjusted
by moving the burner slide in relation to the air holes of the burner slide
guide in the boiler house. Before adding new fuel tablets, always check the water
level and refill the boiler with water to ensure that the boiler does not run dry. The
ratio of fuel tablets to the quantity of water in the boiler is designed so that the boiler
cannot run dry without any added fuel tablets. The burner slide must be completely
pushed in. Important: After the heating process, remove the burner slide from
the guide whilst it is still hot, otherwise unburnt fuel may cause the slide to stick. If
the slide becomes stuck, it can be removed by tilting it slightly to the left or right.
Caution: In order to burn properly, WiTabs dry fuel tablets require a lot
of oxygen That is the reason why during indoor use the room
should be well ventilated. To prevent unpleasant smells, the fuel tablets
should burn out - they should not be blown out. If there is not enough
water in the boiler, place the burner slide on a fireproof plate until the
tablets have completely burnt out .
17. When steam appears (manometer indicating approx. 1 bar), turn once the steam
supply valve to the left to open it. Then turn the flywheel by hand to let the
condensation in the pipes and the cylinder escape. Then the steam engine will start to
operate. The speed of the flywheel can be adjusted through the steam regulator.
18. The condensed water tray must be emptied several times while the steam engine
is running. Before you empty the condensed water tray, turn off the steam regulator
and stop the steam engine.
19. By using the pump, water can be pumped into the boiler whilst the steam engine
ist running. Pour water into the storage tray, it can then be pumped into the boiler by
operating the pump-lever. Caution! If too much cold water is pumped into the boiler,
the steam pressure decreases. After using the steam engine, the remaining water can
be pumped from the storage tray into the boiler and this can then be drained by using
the water drain tap.
20. After the use of the steam engine and its cooling, the Engine should be serviced.
Pour out any water left in the boiler by opening the water drain valve. For this,
unscrew the spring loaded valve, then open the steam whistle by pulling gently on the
chain. This will prevent a vacuum when the residual water is drained off. Be very
careful if the water is still hot! Any water left in the boiler cannot do any damage,
but might leave sediment on the sight glass. Any lime formation on the sight glass or
in the boiler have not to be removed in any case using vinegar or corrosive agent
(advise: use a lime dissolving agent which does not attack the brass and the solder).
The building of sood on the lower side of the boiler does not influence the function
and can be removed with a brush. Finally, dry the model using a clean cloth.
Warranty:
21. All WILESCO steam engines are carefully checked before leaving the factory.
However, if a problem arises, you can return the steam engine to a specialized
distributor or directly to WILESCO. We are sure you will understand that models
which had already been fired or used cannot be replaced by new ones. The most
frequent claims are leaking boilers. The solder will be destroyed if there is not enough
water in the boiler. In this case the solder liquefies drop-shaped and the boiler
becomes leaking. This is an obvious proof that the boiler was fired without enough
water. Please watch always carefully the water level, because the heating without
enough water excludes any warranty claim.
This steam engine is exclusively meant for the above described function.
Subject to technical change without prior notice.
WILESCO wishes you a good time with your steam engine and full steam ahead
Attention ! Avant la mise en marche de ce modèle d'une
machine à vapeur veuillez lire et respecter ce mode d'emploi
soigneusement. Remarques importantes et mesures à
observer pour votre sécurité.
1. Pour des raisons de sécurité, les enfants doivent
utiliser la machine à vapeur uniquement sous la
surveillance d'un adulte (âge conseillé : à partir de 8 ans,
non pas recommandé pour enfants en dessous de 36
mois). Au cours de son fonctionnement et jusqu
refroidissement complet, la machine à vapeur doit être
constamment sous surveillance.
2. Tout défaut de fonctionnement de la machine à vapeur doit être réparé par un
2
!
¡
à son
2
Publicité
