Starting Operation - Bosch POF 1200 AE Instructions D'emploi

OBJ_BUCH-323-002.book Page 20 Friday, December 22, 2006 11:28 AM
Operation

Starting Operation

Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V can
also be operated with 220 V.
Preselecting the Speed
The required speed can be preselected with the
thumbwheel 23 (also while running).
1 – 2 low speed
3 – 4 medium speed
5 – 6 high speed
The values shown in the chart are standard values.
The necessary speed depends on the material and the
operating conditions, and can be determined by prac-
tical testing.
Material
diameter (mm)
Hardwood (Beech)
Softwood (Pine)
Particle Board
Plastics
Aluminium
Switching On and Off
Adjust the depth-of-cut before switching on or off; see
Section "Adjusting the Depth-of-cut".
To start the machine, first push the lock-off button for
the On/Off switch 1 and then press the On/Off
switch 22 and keep it pressed.
POF 1400 ACE: A lamp illuminates the routing area.
To switch off the machine, release the On/Off switch
22.
POF 1400 ACE: The lamp slowly goes out.
Note: For safety reasons, the On/Off switch 22 can-
not be locked; it must remain pressed during the
entire operation.
20 | English
Constant Electronic Control (POF 1400 ACE)
Constant electronic control holds the speed constant
at no-load and under load, and ensures uniform work-
ing performance.
Adjusting the Depth-of-cut
(see figure D)
For coarse adjustment of the depth-of-cut, proceed as
follows:
•
•
Router bit Thumb-
wheel 23
4 – 10 5 – 6
12 – 20 3 – 4
22 – 40 1 – 2
4 – 10 5 – 6
12 – 20 3 – 6
•
22 – 40 1 – 3
4 – 10 3 – 6 •
12 – 20 2 – 4
22 – 40 1 – 3
•
4 – 15 2 – 3
•
16 – 40 1 – 2
4 – 15 1 – 2
16 – 40 1
•
•
•
The adjustment of the depth-of-cut may only
be carried out when the router is switched
off.
Place the machine with the router bit mounted on
the workpiece to be machined.
POF 1400 ACE: Set the fine-adjustment path to
the centre position with the adjustment knob 18.
For this, turn the adjustment knob 18 until the
marks 19 match as shown in the figure. After-
wards, set the scale 17 to "0".
19
Set the step buffer 9 to the lowest position; the
step buffer engages noticeably.
POF 1200 AE: Screw the adjusting screws for
the step buffer 24 halfway in or out.
Loosen the wing bolt for the depth stop 11 so that
the depth stop 13 can be moved freely.
Push the clamping lever for locking of routing
depth 16 in rotation direction
lower the plunge router until the router bit 21
touches the surface of the workpiece. Let go of the
clamping lever 16 again to lock this plunging
depth.
If required, push the clamping lever 16 in rotation
direction to lock it in place.
Push the depth stop 13 downward until it rests on
the step buffer 9. Set the slide with the index mark
12 to the "0" position on the scale for the depth-of-
cut adjustment 14.
Set the depth stop 13 to the required depth-of-cut
and tighten the wing bolt for the depth stop 11.
Pay attention not to misadjust the slide with the
index mark 12 again.
Push the clamping lever 16 in rotation direction
and guide the router to the uppermost position.
and and slowly
1 609 929 K84 • 22.12.06