Bosch POF 1200 AE Instructions D'emploi page 19

OBJ_BUCH-323-002.book Page 19 Friday, December 22, 2006 11:28 AM
The vibration emission level will vary because of the
ways in which a power tool can be used and may
increase above the level given in this information
sheet. This could lead to a significant underestimate
of exposure when the tool is used regularly in such a
way.
Note: To be accurate, an estimation of the level of
exposure to vibration experienced during a given
period of work should also take into account the times
when the tool is switched off and when it is running
but not actually doing the job. This may significantly
reduce the exposure level over the total working
period.
Declaration of Conformity
We declare under our sole responsibility that this
product is in conformity with the following standards
or standardization documents: EN 60745 according
to the provisions of the directives 89/336/EEC,
98/37/EC.
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
06.12.2006, Robert Bosch GmbH, Power Tools Division
D-70145 Leinfelden-Echterdingen
Assembly
Before any work on the machine itself, pull
the mains plug.
Inserting a Router Bit (see figure A)
It is recommended to wear protective gloves
when inserting or replacing router bits.
Depending on the application, router bits are available
in the most different designs and qualities.
Router bits made of high speed steel (HSS) are
suitable for the machining of soft materials, e. g. soft-
wood and plastic.
Carbide tipped router bits (HM) are particularly
suitable for hard and abrasive materials, e. g. hard-
wood and aluminium.
Original router bits from the extensive Bosch acces-
sories program are available at your specialist shop.
Only use clean router bits that are in perfect condition.
• Fold the chip shield 5 down.
• Push the spindle lock button 3 and keep it
pressed. If required, rotate the motor spindle by
hand until it locks.
1 609 929 K84 • 22.12.06
• Loosen the tightening nut 25 with the open-end
spanner 26 (size 19 mm) by turning in rotation
direction .
• Insert the router bit into the collet. The shank of the
router bit must be immersed at least 20 mm into
the collet.
• Tighten the tightening nut 25 with the open-end
spanner 26 (size 19 mm) by turning in rotation
direction . Release the spindle lock button 3.
• Fold the chip shield 5 up again.
Do not insert a router bit with a diameter
larger than 50 mm when the guide bushing is
not mounted. Such router bits do not fit through
the base plate.
Do not tighten the tightening nut of the col-
let without a router bit inserted. Otherwise the
collet can be damaged.
Dust/Chip Extraction (see figure B)
Mounting the Extraction Adapter
The extraction adapter 28 can be mounted with the
hose connection to the front or to the rear. When
mounting with the hose connection in front, the chip
shield 5 must be removed first. Fasten the extraction
adapter 28 with the two knurled screws 29 to the
base plate 6.
To ensure optimum extraction, the extraction adapter
28 must be cleaned regularly.
Connecting the Dust Extraction
Insert an extraction hose (Ø 35 mm) 27 (accessory)
into the mounted extraction adapter. Connect the
extraction hose 27 to a vacuum cleaner (accessory).
The machine can be plugged directly into the recep-
tacle of a Bosch all-purpose vacuum cleaner with
remote starting control. The vacuum cleaner starts
automatically when the machine is switched on.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimen-
tal to health or carcinogenic, use a special vacuum
cleaner.
Mounting the Chip Shield
(see figure C)
Insert the chip shield 5 from the front into the guide in
such a manner that it engages. To remove the chip
shield, grasp it by the sides and pull it off toward the
front.
English | 19