Steinbach Poolrunner S63 Instructions De Service page 6

Masquer les pouces Voir aussi pour Poolrunner S63:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 8
EN
that the packaging is in an undamaged
condition and all parts are in the package. If
you have ordered the package by mail, make
sure that the delivery is complete. Transport
damage must immediately be reported to the
carrier (transport company or parcel). The
responsibility for damages during transit is the
transporter, the supplier is not responsible.
Warranty
Warranty in relation to operation safety and
reliability
is
only
manufacturer under the following conditions:
Ø
The pool cleaner is operated according
to the specifications of the user.
For repairs, only original spare parts are
Ø
used (wearing parts are not subject to
warranty).
Consequential damages
For damage to the product, caused by failure
to follow the manuel recommendations, we
can not
pay.
Position the power supply
The power supply of the device should be
appropriately positioned to allow the cleaner to
reach all corners of the basin.
any accident/damage, the power supply unit
should be steadily placed and fixed at a mini-
mum distance of 3.5m from the pool edge.
Specifications:
• Input voltage: 230 VAC
• Frequency: 50 Hz
• Output voltage: DC (direct current) 24 V
• Input power: 150 W
• Output power: 120 W
• Working cycle: 1 h. / 1,5 h. / 2 h.
• Cable lenght: 9 m
• Maximum cleaning area in the swimming pool: 18 ㎡
• Filtering capacity: 12 m³/h
• Filtering capablity: 180 μm
Working temperature (water):
• Creeping speed: 15 - 18 m/min
Water resistance class: Cleaner: IPX8, power control box: IPX4
Page 6 of 44
accepted
from
In order to avoid
10°C - 32°C
• Ambient temperatur: 10°C - 40°C
Cleaner Structure, Figure 1
Connecting cable, Figure 2,3,4
Description of control panel, Figure 5
Item
Name
1
ON/OFF
the
2
CYCLE
3
LED
Function of jet propulsion, Figure 6
Each on the front and on the back of the cleaner there are two
adjustable control nozzles for the drive in the water. The sucked foul
water is first cleaned through the filter bag and then used for the drive
for the cleaner above the thrusters. The nozzles are adjustable,
depending on the size and pool type, to achieve the best cleaning
effect.
Control nozzles:
The control nozzles can be set to angles between 0 – 40°. The cleaner
will move in a straight or curved line depending on the settings. The
0°/30° setting can be used for most pools. Figure 07
We recommend setting 20°/20° for round pools.
The above are recommending settings and operator can select a
proper nozzle direction based on above principle actual pool situation.
Commissioning
Since you have made your settings, you can put the cleaner carefully
and slowly into the pool. Please refer to the following pictures as the
cleaner may be best placed in the pool.
The cleaner must always be committed or removed to the pool that
the underside of the cleaner facing the pool wall, to avoid possible
scratches on the pool surface.
Care and Maintenance
Function
Detail
Power on or off
Power on or
off
Stop after 1 hour
working, fit for
small swimming
pool
Stop
hour working, fit
for
swimming pool
Stop after 2 hour
working, fit for
large swimming
pool
Flash by corres-
ponding cycle, all
indicators
after one cycle fi-
nish.
Figure 8, 9
Poolrunner S63 | 2017_V1
after
1.5
medium
flash

Publicité

Table des Matières
loading

Table des Matières