GoodHome hyana 500W Mode D'emploi page 31

Use
FIG. 10
Always handle the remote control with great care and place it within the
special plastic container for wall mounting, included in the packaging.
Do not drop the remote control nor leave it exposed to direct sunlight. Do
not spray water or other liquids onto the remote control. Do not place the
remote control on top of the appliance or close to intense sources of heat.
INSERTING OR REPLACING THE BATTERIES
1) Remove the cover on the back of the remote control.
2) Insert two "AAA" LR03 1.5 V alkaline batteries. When inserting the
batteries, always respect the polarity (+ and -) indicated on the battery
and the appliance.
3) Put the cover back.
Never use flat batteries and new batteries together, always use batteries
of the same type and brand.
Flat batteries must be removed from the appliance immediately and
disposed of appropriately. When replacing the batteries or disposing
of the remote control, the batteries must be removed and disposed
of in compliance with current legislation as they are harmful to the
environment. Never throw batteries into a fire.
Keep batteries away from children. Children may change batteries only if
supervised by an adult. Remove the batteries if you will not be using the
appliance for a long period. Take appropriate precautions when handling
leaking batteries!
Avoid contact with the skin, eyes and mucous membranes.
If you come into contact with the battery liquid, rinse the parts affected
immediately with plenty of water and seek medical advice immediately.
OPERATION
STAND-BY STATE BY RC
In "Standby" mode the LCD displays the Standby icon, the hour and day of
the week.
All the operating modes are suspended ("Pilot Wire" included), but the
appliance is powered and waiting for command reception. To turn on or
off the appliance, press the "Standby" key. The radiators turns on in the
previously selected operating mode and emits a beep.
In "Chrono" mode the display shows the time, in the other modes the
temperature setting is displayed.
The entry into "Standby" mode is signalled by means of a double beep, the
exit from "Standby" mode by means of a long beep.
TURNING ON FOR THE FIRST TIME
MAX: 2 m
After inserting the batteries, set the year, month, day of the week and time.
Adjust the day of the week by using the "+" and "-" keys (1=MON, 2=TUE,...
7=SUN), then confirm by pressing the "Mode" selection key. The hour starts
flashing. In the same way, adjust the hour by using the "+" and "-" keys and
confirm with "Mode" selection key. Repeat the same procedure for the
minutes. The year of start is 2019.
PILOT WIRE
TO ACTIVATE THE "PILOT WIRE" MODE
Press the "Mode" selection key until the
Users can only set the "Comfort" temperature on the appliance. Select the
desired temperature set point by using the "+" or "-" keys.
The home must be fitted with an automation system supporting this type
of technology. In this case, correct transmission of the programming
commands can be verified using the following diagram according to the
mode set: (see table 1).
The icon showing the mode selected on the control unit (Standby,
Comfort, Night/Eco, Anti-Freeze) is displayed together with the icon.
If the Pilot Wire programmer is not connected, "Comfort" operating mode
is selected automatically.
Mode Comfort Night/
Eco
(Comfort
-3,5 °C)
Signal to be
transmitted
Voltage XXX volt 230 volt
between
Pilot Wire
and neutral
wires
COMFORT
The "Comfort" temperature corresponds to the temperature desired by
the user. All "Pilot Wire" commands are disabled.
Press the "Mode" selection key until the icon appears on the LCD.
Select the desired temperature set point by using the "+" or "-" keys.
The temperature can be choosen in the interval between 13 °C and 30 °C.
The behavioural indicator allows you to check if the chosen temperature
set point is aligned with the recommended guidelines, in order to avoid the
waste of energy and reduce the energy consumption.
An arrow will appear by one of the three colored bars that represent
the energy consumption in a qualitative way, according to the
following scheme:
(a) Green Dark: The chosen temperature set point is already lower than
the recommended. Heating on.
(b) Green Light: The chosen temperature set point is adequate, but it would
be better to further decrease it. Heating on.
(c) Red: The chosen temperature set point is high, it would be better to
decrease it. Heating on.
(d) Green Dark Flashing: The chosen temperature set point is already
lower than the recommended. Heating off.
(e) Green Light Flashing: The chosen temperature set point is adequate,
but it would be better to further decrease it. Heating off.
(f) Red Flashing : The chosen temperature set point is high, it would be
better to decrease it. Heating off.
NIGHT/ECO
In "Night/Eco" mode the temperature set point must not be higher than
"Comfort" temperature set point.
If the "Comfort" temperature is set below the "Night/Eco" temperature,
the latter will be automatically adjusted accordingly.
Press the "Mode" selection key until the icon
Select the desired temperature set point by using the "+" or "-" keys.
The use of this operating mode is recommended in nighttime hours and
in case no people are in the room for more than 2 hours. Default night is T
comfort -3°C.
ANTI-FREEZE
In "Anti-Freeze" mode the temperature set point is fixed at 7 °C. The appliance
starts heating when room temperature goes under 7 °C and with low energy
consumption it prevents the room temperature from reaching freezing point.
29 31
icon appears on the LCD .
Anti- Standby Comfort Comfort
Freeze -1°C -2°C
115 volt 115 volt 230 volt 230 volt For
Negative Positive For an an interval
interval of 7 s
of 3 s
appears on the LCD.