Maintenance; Daily Maintenance; Extended Maintenance; Accessories - amspray DSP 1400 Serie Notice D'utilisation

8. Continue to trigger the gun for
approximately 30 seconds.
9. Turn the PRIME/SPRAY knob to
PRIME.
10. Trigger the gun to remove any
pressure which may still be in
the hose.
11. Lock the spray gun off.
12. Turn the motor switch to OFF.
Preparing the Sprayer for Long-term Storage
1. Remove the tip assembly and raise the suction set above
the cleaning solution.
2. Turn the motor to ON.
3. Turn the PRIME/SPRAY knob to SPRAY.
4. Remove the large suction tube from the inlet valve and
point the gun into the cleaning bucket.
5. Unlock the gun and trigger it into the cleaning bucket until
the hose is pumped dry.
6. Turn the PRIME/SPRAY knob to PRIME.
7. Clean the threads of
the inlet valve with a
damp cloth.
8. Fill the inlet valve with a
light household oil.
Slowly increase the
pressure to distribute the
oil through the pump.
Also add oil to top
bushing of unit in order
to prolong seal life.
9. Turn the PRIME/SPRAY
knob to SPRAY to distribute the oil.
10. Replace the large suction tube onto the inlet valve.
11. Turn the PRIME/SPRAY knob to PRIME.
12. Trigger the gun to remove any pressure which may still be
in the hose.
13. Lock the spray gun off.
14. Turn the motor switch to OFF.
15. Remove and clean the suction set filter in clean water or
the appropriate solvent. Use a soft brush. Return the
suction set filter to its original position.
16. Wipe the entire unit, hose and gun with a damp cloth to
remove accumulated paint.
NOTE: Thorough cleaning and lubrication of the
sprayer is the most important step you can
take to ensure proper operation after storage.
NOTE: If you spray oil-or solvent-based material, the
following cleaning steps must be followed in
addition to the steps in the owner's manual to
properly clean and lubricate the pump before
storage.
1. Flush the pump with the appropriate solvent as
recommended on the paint manufacturer's label.
Follow the steps in the owner's manual.
2. After flushing with solvent, run warm, soapy water
through the pump to remove the solvent material. The
solvent must be removed to allow proper lubrication of
the pump prior to storage.
3. Lubricate the pump using a light household oil as
described in the owner's manual.

MAINTENANCE

Daily Maintenance

The only daily maintenance necessary is thorough cleaning.
English
Inlet
valve
Follow the cleaning procedures in this manual.

Extended Maintenance

Some pump parts eventually wear out from use and must be
replaced. The following list indicates the available repair kits
for the parts replaced by each kit. However, pump
performance is the only reliable indicator of when to replace
wear parts. Refer to the Troubleshooting section for more
information on when to use these kits.
Kit Part # Description
0512221 Fluid Section Seal Kit (1400 and 1550 Series)
0512222 Valve Replacement Kit (1400 and 1550 Series)
0512223 Fluid Section Seal Kit (1700,1900, 2100 Series)
0512224 Valve Replacement Kit (1700,1900, 2100 Series)

ACCESSORIES

Part # Description
0154908 Separating Oil
0154830 Hose, Whip End, 5' x 3/16"
0270192 Hose, Wireless, 25' x 1/4"
0270118 Hose, Wireless, 50' x 1/4"
0093896 Hose Connector, 1/4" x 1/4"M
0088154 Pressure Gauge
0512130 Tip Extension, 12"
0512131 Tip Extension, 24"
0152001 Power Roller Gun Attachment
0155206 9" Roller Cover, 3/8" Nap
0152307 9" Roller Cover, 1/2" Nap
0155208 9" Roller Cover, 3/4" Nap
0152310 9" Roller Cover, 1-1/4" Nap
0501002 GX-08 Four Finger Metal Airless Spray Gun
0501004 GX-07 Two Finger Metal Airless Spray Gun
0501026 GX-06 Two Finger Plastic Airless Spray Gun
0501029 GX-10 Two Finger Metal Airless Spray Gun w/Swivel
0501010 Guard Assembly, F-Thread
0501011 Guard Assembly, G-Thread
0512132 3 Foot Pole Extension w/Swivel
0512133 6 Foot Pole Extension w/Swivel
0154839 All Guard Pump Protector
0512134 180 Degree Swivel
0512135 F- to G-Thread Adapter
0154832 Suction Tube Filter (2 Pack)
0501411 411 Trade Spray Tip
0501413 413 Trade Spray Tip
0501415 415 Trade Spray Tip
0501417 417 Trade Spray Tip
0501419 419 Trade Spray Tip
0501515 515 Trade Spray Tip
0501517 517 Trade Spray Tip
0501519 519 Trade Spray Tip
0093930 Anti-Seize Compound
0156113 TR-10 Telescoping Roller, 9", 3/8" Nap
Choosing the Correct Spray Gun Filter
Use the proper gun filter based on the type of material being
applied as shown below.
Part No. Tip Size
0154918 .011
0154675 .013 - .015
0154842 .017 - .023
0154919 .023 and up
10 © 2001 Wagner Spray Tech - All rights reserved.
Filter Mesh Color of Qty.
Type Number Filter
Body
Extrafine 180 mesh red 2 pack
0.084 mm
Fine 100 mesh yellow 2 pack
0.140 mm
Medium 50 mesh white
2 pack
0.315 mm
Coarse 30 mesh green
2 pack
0.560 mm