Canadian Spa North American 60Hz Mode D'emploi page 19

Spa operation - Azure i262 CS Control Panel
The Temp Lock Message appears on the Screen after the
Temperature is Locked. To Exit the Message, Touch Back Home or
Select . To Unlock the Control Panel, you Must Return to the Settings
Menu, and with Temp Lock Highlighted, Touch Select to Unlock the
Water Temperature.
Set Over Temperature - If you want a temporary Water Set
Temperature higher than 104ºF (40.0°C), you Must Set it in the Over
Temp Menu. Underwriters Laboratory requires this type of Control
because the Consumer Product Safety Commission has determined
that soaking in Water Temperatures above 104ºF (40.0°C) can
sometimes be Dangerous.
To Increase the Water Set Temperature to 105ºF (40.5°C) or 106ºF
(41.0°C), in Navigation Mode, with Settings Highlighted, Touch Select
to Open the Settings Menu. Scroll Down , and with Over Temp
Highlighted, Touch Select or Right to Open the Over Temp Menu.
You must confirm your intention to temporarily Set a Water Tempera-
ture higher than 104°F (40.0°C). Touch Select to continue to the Over
Temp Menu to raise the Water Temperature above 104ºF (40.0°C).
Scroll to the desired Water Set Temperature and Touch Select to Set
that Water Temperature.
Touch Select again to verify your selected Set Temperature. Touch
Select again to clear the last Warning Message, and your Over Temp
selection will be recorded to the Event Log. The Water will be Heated
to the selected Set Temperature one time. You will have to come back
to the Over Temp Menu to raise it above 104ºF (40.0°C) again.
Set Time and Date - Once you Set the Current Time of Day, Day of
the Week, and Calendar Date, it will be maintained in System
Memory, and it should not have to be Set again except for Daylight
Savings Time changes. The Calendar Date is only used for the Event
Log which is in the Service Menu and Settings Menu. Only the Time
of Day and Day of the Week are used for Setting Filter Cycles and
other Timers. You also have a choice of regular 12 Hour Time Display
with AM and PM, or 24 Hour Military Time.
Owners Manual
Message will
Auto close in
a few seconds
To Set Time & Date, in Navigation Mode, with Settings Highlighted,
Touch Select to Open the Settings Menu. Scroll Down , and with Set
Time & Date Highlighted, Touch Select or Right to Open the Set Time
& Date Menu.
To Set the Time of Day, with Set Time Highlighted, Touch Select or
Right to Open the Set Time Menu. To change the Time of Day, Move
Right to Hours or Minutes, and then Touch Up or Down to change the
Time. Touch Left to Save the new Time and Exit back to the Set Time
& Date Menu, or Touch Back Home to Not Save the new Time and
return to the Home Screen.
To Set the Day of the Week, with Set Day Highlighted, Touch Select
or Right to Open the Set Day Menu. To change the Day of the Week,
Move Right to Today's Day, and then Touch Select to change to To-
day's Day of the Week. Touch Left to Save the new Day and Exit back
to the Set Time & Date Menu, or Touch Back Home to Not Save the
new Day and return to the Home Screen.
To Set Today's Date, with Set Date Highlighted, Touch Select or Right
to Open the Set Date Menu. To change Today's Date, Move Right to
Month, Day, or Year, and then Touch Up or Down to change the Month,
Day, or Year. Touch Left to Save the new Date and Exit back to the Set
Time & Date Menu, or Touch Back Home to Not Save the new Date
and return to the Home Screen.
To turn 24 Hour Time Display On or Off, with 24 Hour Highlighted,
Touch Select . When you Touch Back Home to Return to the Home
Screen, the Time will read 1:00 - 24:00 Hours.
Set Water Temperature - The Water Set Temperature is the Water
Temperature that the Spa Heater will maintain in your Spa. It can be
Set from the Home Screen with a Single Button Touch, or in
Navigation Mode from the Control > Temperature Menu.
From the Home Screen - Set Temperature by using the Temp Button.