Cleaning, Maintenance, Storage, Transport And Ordering Of Spare Parts; Oil Level Check - Bavaria BPM 46 S Mode D'emploi D'origine

Anleitung_BPM_46_S_SPK7__ 24.10.13 08:16 Seite 25
8. Cleaning, maintenance, storage,
transport and ordering of spare
parts
Important:
Never work on or touch any current-conducting parts
of the ignition system while the engine is running. Pull
the spark plug boot from the spark boot before doing
any maintenance or assembly work. Never carry out
any work on the equipment while the engine is
running. Work that is not described in these operating
instructions, should only be carried out by authorized
workshops.
8.1 Cleaning
The lawn mower should be cleaned thoroughly every
time after it has been used. This particularly applies to
its underside and the blade mount. For this purpose,
tilt the lawn mower onto its left side (opposite the oil-
filler neck).
Note: Before placing the lawn mower on its side, fully
drain the fuel tank using a petrol extraction pump. Do
not tilt the lawn mower by more then 90 degrees. It is
easiest to remove dirt and grass immediately after
mowing. Dried grass remnants and dirt may impair
the mowing operation. Check if the grass ejector
chute is free of grass remnants and remove any if
necessary. Never clean the mower using a water jet
or a high-pressure cleaner. Ensure that no water can
get into the interior of the equipment. Do not use
aggressive cleaning agents such as cold cleaners or
petroleum ether.
8.2 Servicing
Please refer to the supplied petrol service
manual for information on the maintenance
intervals.
Important: Dispose of soiled maintenance material
and operating materials at the appropriate collection
point.
8.2.1 Axles and wheel hubs
A thin coating of grease should be applied to the
axles and wheel hubs once per season. To do so,
remove the wheel caps with a screwdriver and loosen
the fastening screws on the wheels.
8.2.2 Blades
For safety reasons, have all blade sharpening,
balancing and mounting work carried out by an
authorized service center. To achieve optimal results,
we recommend to have the blades checked once a
year.
Changing the blades (Fig. 8)
When changing the cutting unit, be sure to use only
genuine replacement parts. The identification mark
on the blade must correspond with the number
specified in the spare parts list. Never install a blade
from a different manufacturer.
Damaged blades
If, in spite of all caution, the blade comes into contact
with an obstacle, switch off the engine immediately
and pull the spark plug boot. Tilt the mower to the
side and check the blade for damage. Damaged or
bent blades must be replaced. Never straighten a
bent blade. Never work with bent or heavily worn
blades as this will result in vibrations, causing further
damage to the mower.
Important: Risk of injury when working with a
damaged blade.
Resharpening the blade
The blade edges can be resharpened with a metal
file. To avoid imbalance, the blade resharpening work
should only be carried out by an authorized service
center.

8.2.3 Oil level check

Important: Never run the engine with no or too little
oil. This can cause serious damage to the engine.
Checking the oil level
Place the lawn mower on a level and straight surface.
Unscrew the oil dipstick (Fig. 9a/Item 7a) by turning it
counter-clockwise and wipe the dipstick. Re-insert
the dipstick into the filler opening as far as it will go
but do not screw it in. Pull out the dipstick, hold it
horizontally and read off the oil level. The oil level
must be between the two marks min. and max. on the
oil dipstick (Fig. 9b).
Changing the oil
The engine oil is best changed at room temperature.
Place a flat oil drip tray beneath the mower.
n
Open the oil filler plug (Fig. 9a/Item 7a)
n
Tilt the lawn mower over the oil drip tray.
n
Let the oil run out through the oil filler opening.
n
Stand the lawn mower back on its wheels.
n
Fill in engine oil up to the top mark on the oil dip
n
stick
Dispose of the used oil in accordance with
n
applicable regulations.
8.2.4 Care and adjustment of the cable pulls
Oil the cable pulls at regular intervals and check that
they move easily.
GB
25