DeWalt DCD720 Traduction De La Notice D'instructions Originale page 40

EN GLI SH
Dual Range Gearing (fi g. 1)
The dual range feature of your drill allows you to shift
gears for greater versatility.
1. To select speed 1 (high torque setting), turn
the tool off and permit it to stop. Slide the gear
shifter (c) forward (towards the chuck).
2. To select speed 2 (low torque setting), turn the
tool off and permit it to stop. Slide the gear
shifter back (away from the chuck).
NOTE: Do not change gears when the tool is
running. Always allow the drill to come to a complete
stop before changing gears. If you are having trouble
changing gears, make sure that the dual range
gear shifter is either completely pushed forward or
completely pushed back.
Worklight (fi g. 1)
There is a worklight (e) located between the chuck
and the paddle switch (a).The worklight is activated
when the trigger switch is depressed, and will
automatically turn off 20 seconds after the trigger
switch is released. If the trigger switch remains
depressed, the worklight will remain on.
NOTE: The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Keyless Chuck (fi g. 1)
WARNING: Do not attempt to tighten
drill bits (or any other accessory) by
gripping the chuck and turning the tool
on. Damage to the chuck and personal
injury may result. Always lock off paddle
switch when changing accessories.
WARNING: Always ensure the bit
is secure before starting the tool. A
loose bit may eject from tool causing
possible personal injury.
Your tool features a 3/8" keyless chuck for greater
convenience. To insert a drill bit or other accessory,
follow the steps listed below.
1. Lock the paddle switch in the off position
as described in Forward/Reverse Control
Button.
2. Grasp the chuck (k) with one hand and rotate
counterclockwise. Rotate far enough so that the
chuck opens sufficiently to accept the desired
accessory.
3. Insert the bit or other accessory about 19 mm
(3/4") into the chuck and tighten securely by
holding the chuck and rotating in the clockwise
direction.
To release the accessory, repeat step 2 listed above.
38
DEEP HEX POCKET (FIG. 1)
Your tool features a deep hex pocket (d) which
is through and behind the chuck (k). This allows
for a 2" (51 mm) or longer 1/4" hex shank bit
to be inserted farther into the unit for close-up
applications. With the chuck jaws fully open (as
described in Keyless Chuck) insert a 1/4" hex
shank bit fully into and through the chuck. The
chuck can then be tightened as stated under
Keyless Chuck.
Belt Hook and Bit Clip (fi g. 1)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
WARNING: To reduce the risk of
serious personal injury, DO NOT
suspend tool overhead or suspend
objects from the belt hook. ONLY hang
tool's belt hook from a work belt.
WARNING: To reduce the risk of
serious personal injury, ensure the
screw holding the belt hook is secure.
IMPORTANT: When attaching or replacing the
belt hook or bit clip, use only the screw (g) that is
provided. Be sure to securely tighten the screw.
The belt hook (f) and bit clip (h) can be be attached
to either side of the tool using only the screw (g)
provided, to accommodate left- or right- handed
users. If the hook or bit clip is not desired at all, it
can be removed from the tool.
To move belt hook or bit clip, remove the screw
(g) that holds it in place then reassemble on the
opposite side. Be sure to securely tighten the screw.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.