Raider PRO RDP-SCDI20 Set Mode D'emploi Original page 20

20 www.raider.bg
- replace them as soon as possible.
6.6. Storage of batteries, chargers and rechargeable tools. Conditions for use.
Store the charger and the battery charger only in a dry place and at an ambient temperature of 10-
30 ° C. Protect them from moisture and direct sunlight. Only recharge fully charged rechargeable
batteries / charged at least 40% /. When operating, use the battery charger, angle grinder and
battery only in a dry place and at an ambient temperature of 0-45 ֯ C.
6.7. Protect the lithium-ion battery from frost. Rechargeable batteries that are stored below 0 ֯ C for
more than 60 minutes should be discarded.
6.8. When handling batteries, be aware of the electrostatic charge. Electrostatic discharges cause
damage to the electronic protection system and battery cells. Beware of the electrostatic charge and
never touch the battery poles.
7. Operation and settings. Switching on. Switching off.
7.1. Switching on - press the switch button (1).
7.2. Switching off - release the switch button (1).
7.3. Rotational speed control.
Screwing or drilling speed can be controlled during operation by increasing or decreasing pressure
on the switch button (1). Speed control enables soft start, which prevents drill slip when drilling in
gypsum or glaze and helps to control the operation when screwing and unscrewing.
7.4. Overload clutch. Torque control.
Setting the ring (3) in given position causes permanent setting of the clutch to specified torque.
When the set torque is reached, overload clutch releases automatically. It prevents screwing screws t
deep or damaging the drill.
Different screws and materials require different torque to be applied.
The bigger number corresponding to given position, the bigger the torque.
Set the ring (3) to specified torque.
Always start operation with low torque.
Increase the torque gradually until appropriate value is set.
Use higher settings to unscrew screws.
When drilling chooses settings marked with the drill symbol. When this setting is set, the torque is
the greatest.
Knowledge how to choose appropriate settings comes with practice.
Setting the ring in the drilling position deactivates the overload clutch.
7.5. Change of gear.
Drill features gear switch (5), which broadens the range of rotational speed.
Gear I: small speed range, big torque;
Gear II: big speed range, low torque.
Set the switch in appropriate position depending on the works performed. Turn the spindle slightly
if the switch cannot be moved.
Never change the switch (5) position under operation of the drill. It may damage the power tool.
7.6. Working tool installation.
Set the direction selector switch (2) in middle position.
7.7. Left - right direction of rotation.
Choose direction of spindle rotation with the selector switch (2).
Right rotation - move the switch (2) to the extreme left position.
Left rotation - move the switch (2) to the extreme right position.
Do not change direction of spindle when the spindle is rotating.
7.8. Drilling.
When you need to vent large diameter, is recommended first to break a small opening, which will
then be drilling to the desired size. This will prevent overloading the drill. Drilling deep holes should
be done gradually, as periodically removed from the drill hole to remove chips or dust. If during drilling
to drill block up in holes, you should exclude drill. Use a change of direction of rotation to remove
the drill from the hole. Drill must be kept in alignment with the hole. Ideally, the drill should be placed
perpendicular to the surface of the material being processed. If the condition for perpendicularity is
not respected at work can lead to trapped or breakage in drill hole and injury to the user. Continued
drilling at low speed the engine from overheating threatens. Must make periodic breaks during work or
to allow the drill to work on no-load maximum speed for about 3 minutes. Do not obscure the openings
in the hull used for ventilation of the engine.