Inglesina TRILOGY Manuel D'instructions page 28

lining periodically for correct maintenance.
HUGGY INFANT CAR SEAT (IF AVAILABLE)
ATTACHING THE INFANT CAR SEAT TO THE CHASSIS
fig. 32 Take the infant car seat from the handle and attach
it to the chassis in correspondence of the housings on
both sides of the structure and place it solely in rear facing
position.
fig. 33 CAUTION: make sure that the infant car seat is
properly attached before use.
DETACHING THE INFANT CAR SEAT FROM THE CHASSIS
fig. 34 Use the lever (S1) on the rear of the infant car seat.
fig. 35 Simultaneously, lift the seat by holding it by the
handle.
To use the Huggy infant car seat properly, refer to the
dedicated manual.
PUSHCHAIR SEAT
ATTACHING THE PUSHCHAIR SEAT TO THE CHASSIS
fig. 36 Attach the pushchair seat to the chassis, in
correspondence of the housings on both sides of the
structure.
fig. 37 CAUTION: make sure that the pushchair seat is
properly attached before use.
fig. 38 The pushchair seat can be used in rear facing and
forward facing position, and the chassis can be folded with
the pushchair seat attached.
DETACHING THE PUSHCHAIR SEAT FROM THE CHASSIS
fig. 39 Press the handles (R5) simultaneously and lift the
pushchair seat off the chassis.
CAUTION: do not, under any circumstance, carry out this
operation with the baby inside.
ADJUSTING THE BACKREST
fig. 40 The backrest can be adjusted to 3 positions; use
the central device (R6) and bring the backrest to the desired
position.
ADJUSTING THE FOOTREST
fig. 41 To lower the footrest, use both levers (R7)
positioned on the lower part and simultaneously press them
downwards.
fig. 42 To lift the footrest, simply pull it upwards and it
shall automatically lock into position.
SAFETY BELTS
fig. 43 Ensure that the safety belts are inserted in the
eyelets at the height of the shoulders or immediately above.
If the position is not correct, remove the belts from the first
pair of eyelets and reinsert them in the second one; always
use eyelets at the same height.
fig. 44 Make sure that the back strap is properly inserted in
the ends of the waist one.
fig. 45 Fasten the ends of the strap belt to the central
buckle.
fig. 46 The waist strap must always pass through the side
loops (R8) and, when being used, it must be adjusted in order
to properly secure the baby.
fig. 47 Always use the crotch strap together with the waist
one, adjusting both of them properly.
CAUTION! Failure to comply with this precaution can
cause the baby to fall or slide out, with serious injury
risks.
ATTACHING THE HANDRAIL
fig. 48 Mount the handrail (R1) by pressing the buttons
(R9) and attach it in correspondence of the relative housings
on the pushchair seat (R10).
28
fig. 49 The handrail can be open on one side or fully
removed; to open it, press the button (R9) and remove it from
its housing; to remove it, repeat the procedure on the other
side.
ATTACHING THE HOOD
fig. 50 The hood is mounted onto the stroller by
positioning it in correspondence of the 2 housings (R11)
on the pushchair seat and inserting the slides (H1), pushing
until they both click into place.
fig. 51 Fasten the press studs of the lining to the backrest,
starting with the upper ones (H2) and then with the lower
ones (H3).
fig. 52 To adjust the hood, simply accompany it to the
desired position.
DETACHING THE HOOD FROM THE STROLLER
fig. 53 To remove the hood from the stroller, unfasten the
press studs that secure the lining to the backrest (H2-H3).
fig. 54 Then adjust the lever (H5) and simultaneously
extract the hood from the housings (R11) on the pushchair
seat.
HOOD LINING MAINTENANCE
fig. 55 The hood lining can be removed to allow for its
correct maintenance. Unfasten the buttons (H6) on both
hood joints (H7).
fig. 56 Detach both joints (H7) from the binding (H8) and
remove the lining.
fig. 57 To remount the lining, insert both bindings (H8) in
the guides on the internal lining.
fig. 58 Insert the bindings (H8) in their housings on both
joints (H7), until fully attached.
MUFF (IF AVAILABLE)
fig. 59 Place the muff (R3) making it pass under the
handrail.
fig. 60 Button up the central binding (F1), making it pass
through the ring (F2).
fig. 61 The muff reverse can also be attached in a suitable
position for protecting the child against cold weather.
fig. 62 The muff can be used on both rear facing and
forward facing pushchair seats.
RAIN COVER (IF AVAILABLE)
fig. 63 To mount rain cover (R4), place it on the hood and
button up the snap fastners on the side (P1).
fig. 64 Fasten the elastic straps (P2) around the front
tubes, in correspondence of the wheel assembly.
MAINTENANCE OF THE LINING
It is recommended to remove the lining periodically to
provide for its correct maintenance.
fig. 65 Detach the two lower elastic straps (R12) from the
footrest, removing it from its supports (R14).
fig. 66 Unfasten the buttons on the seat (R15).
fig. 67 Remove the elastic strap (R16) and unfasten the
buttons (R17) on both sides of the pushchair seat.
fig. 68 Unfasten the buttons on the eyelets and on the
backrest (R18).
fig. 69 Extract the shoulder pads from the back straps.
fig. 70 Remove the waist strap from the side loops (R8) ,
taking care to make the first tooth of the central buckle pass
through the side loop before removing it completely.
fig. 71 Remove the crotch strap from the protection built
into the lining (R19).
fig. 72 Pass the shoulder straps and the crotch strap
through the eyelets on the lining and remove it completely.
WARNING: make sure that the lining has been properly
reassembled before use.