Additional Functions; Display Blanking; Colour Balance / White Balance; Key Lock - IMG STAGELINE PARL-74RGBW Mode D'emploi

4) Set the desired sub-address with the button UP
or DOWN.
5) Press the button ESC / MENU to return to the
main menu; the display shows
6) Select the menu item
and press ENTER to confirm.
7) Select the submenu item
UP or DOWN and press ENTER to confirm.
8) If the display shows
has been deactivated, activate it with the button
UP ( ).
9) Adjust the spotlight for control via 8 DMX chan-
nels chapter 8.2 (menu item
).
In order to operate the spotlight, set DMX channel 8
on the light controller to the DMX value correspond -
ing to the sub-address of the spotlight (
chapter 10.1.5).
9

Additional Functions

9.1 Display blanking

If you prefer the display (1) to be blank during oper-
ation, activate the automatic display blanking:
1) Press the button ESC / MENU repeatedly until
you enter the main menu.
2) Select the option
button UP or DOWN and press ENTER to con-
firm
3) Select the submenu item
UP or DOWN and press ENTER to confirm.
4) If the display shows
has been deactivated, i. e. the display is always
on. When the display blanking has been acti-
vated (
seconds after the last button was pressed; it is
switched on again when a button is pressed.
Select the desired option with the button UP or
DOWN.

9.2 Colour balance / white balance

It is possible to shift the balance between the three
primary colours red, green and blue. This will also
change the light colour for combined white light (if
the three colours are used in addition to the white
LEDs), e. g. to balance differences to other spot-
lights if the LED spotlight is controlled together with
them.
To activate the colour balance function and to set
the correction values:
16
with the button UP
with the button
, i. e. sub-addressing
in the main menu with the
with the button
, the display blanking
), the display is switched off a few
1) Press the button ESC / MENU repeatedly until
you enter the main menu.
2) Select the option
again.
button UP or DOWN and press ENTER to con-
firm.
3) Select the submenu item
UP or DOWN and press ENTER to confirm.
4) If the display shows
tivated, i. e. the correction values adjusted are
not taken into account. Activate the function with
the button UP or DOWN (
5) Press the button ESC / MENU to return to the
main menu; the display only shows
, setting
6) Select the menu item
7) Press the button ENTER. The display shows the
last primary colour adjusted, red ( ), green ( )
ID table,
or blue ( ) and the corresponding correction
value (0 – 255). This is the maximum brightness
to be set for this colour.
8) Set the value for the colour selected with the but-
ton UP or DOWN.
9) To switch between the colours, press the button
ENTER.

9.3 Key lock

To prevent accidental operation, a key lock can be
activated.
Activating the key lock:
1) Press the button ESC / MENU repeatedly until
you enter the main menu.
2) Select the option
button UP or DOWN and press ENTER to con-
firm.
3) Select the submenu item
UP or DOWN and press ENTER to confirm.
4) The display shows
deactivated. Activate the function (
the button UP or DOWN. After approx. 10 sec-
onds it is no longer possible to operate the spot-
light via the buttons ESC / MENU, UP and
DOWN.
Deactivating the key lock
1) Press the button ENTER twice.
2) Press the buttons in the following sequence:
UP → DOWN → UP → DOWN. Each time you
press a button, a horizontal line appears on the
display.
3) Press the button ENTER to terminate the input.
in the main menu with the
with the button
, the function is deac-
).
again.
with the button UP.
in the main menu with the
with the button
, i. e. the key lock is
) with