Automatismos Pujol WINNER PRO V17 400/200 EF Instructions De Montage Et D'installation page 7

Kg.
TYPE
WPRO V17 400/200 EF 7
WPRO V17 400/200 6
WPRO V17 600/200 EF 7,8
WPRO V17 600/200 6,8
WPRO V17 630/200 EF 8,3
WPRO V17 630/200 7,3
WPRO V17 1260/200 EF 12,9 220-240V 50/60 1260
WPRO V17 1260/200 11,9 220-240V 50/60 1260
Com pone nts to be ins talle d according to EN12453
USE OF THE CLOSURE
Expert people
TYPE OF CONTROL
(outside a public
area *)
In the presence of
someone
A
With pulses in sight
C o E
(eg sensor)
With impulse not in
sight (on remote C o E
control)
Automatic CyD,oE
* A typical example is the closures that do not access the public w ay.
A: Pulsating command w ith dead man ( w ith sustained action),
B: Key selector w ith dead man.
C: Regulation pow er motor.
D: Sensors to detect obstacles and / or other devices that limit f orces
betw een limits of standards EN 12453 - Appendix A.
E: Photocells placed as indicated in EN 12445 point 7.3.2.2 f or the w hole
height of the door up to a maximum of 2.5 m).
MOUNTING OPERATIONS
Drill in the shutter's central shaft (Fig. 4) one hole Ø 10 mm. in order the operator doesn't turn, and
another Ø 12 mm. for the electric wire. If possible, place the operator in the centre of the shutter's
shaft in an easy position for opening the micro-switches lid to make the wire and the regulation of
the limit switches. In case of electric brake, make another drill of Ø 10 mm. for the cable of the
manual release.
Open the pulley unscrewing the M8x25 screws remove the plastic roller band without folding it and
keep it in a clean place. Separate the gear-motor's body removing the 4 screws with the 6mm. (fig.
5). hexagonal wrench.
Couple the two parts of the gear-motor around the door's shaft and joint them screwing the 4
screws on the gear-motor's support (fig. 6)
Tighten the M10x40 screw (Fig. 8 A) entering it into the Ø 10 mm. hole of the shutter's shaft.
Put again the plastic roller band in its place.
Apply again the pulley by coupling the two parts and tighten the screws.
Screw also the M10x40 (Fig. 8 B), bi-motor (fig. 10 B). Pressing on the shaft till the gear-motor is
blocked and tighten the nut.
The operator should be fixed, lined and the pulley must turn freely.
Make a hole Ø 12 mm. in the last canvas of the shutter at the same location of the hole and nut M10
of the pulley (Fig. 11). If the shutter is waved or not regular, it is necessary to couple a flat metal piece
of 1 meter to the pulley.
Travel the electric cable trough the shaft's hole de Ø 12 mm. (Fig. 14), avoiding any contact with the
rotating parts and make the wires. In case of motor with electric brake travel also the brake cable
through the hole of Ø 12 mm. drilled in the shaft, and mount the manual release.
For a proper release the flexible cable of the brake should not do any exaggerated curve.
ELECTRIC WIRE (Fig. 14)
It is very important to respect the connection of the common of the motor (N) and the earth
connection. The model with electro brake comes already wired. If the automatism is not
provided with electro brake, bridge the contacts (A, B fig 14). With electro brake, remove the
bridge and on the same terminals connect the reel. SECURITY STANDARD: The connection wires
should come from a differential switch.
CHECKING THE OPERATION DIRECTION (Fig. 16)
Place the closing stop collar (C) until the click of the opening micro-switch is heard (fig. 16) Give
power, if the motor stops at closing it's correct. If not, cut the power and change the position of the
phase wires, or the two wires that go to the control unit, or activate it manually by means of the push
button or the key switch. Continue respecting the common jumper of the motor (N).
A
V HZ W
220-240V 50/60 400 2,15
220-240V 50/60 400 2,15
220-240V 50/60 600 2,7
220-240V 50/60 600 2,7
220-240V 50/60 630 2,8
220-240V 50/60 630 2,8
5,6
5,6
Expert people Unlimited use
(public area)
B X
C o E CyD,oE
CyD,oE CyD,oE
CyD,oE CyD,oE
IP
Nm Kg.
105 100 20 10 20
110 105 20 10 20
168 160 20 10 20
178 170 20 10 20
189 180 20 10 20
199 190 20 10 20
357 340 20 10 20
367 350 20 10 20
1
Bipolar switch
2 Flashlight
Electronic board with
3
built-in receiver
Manual unlocking of the
4
actuator
Key switch 2 and
5
external brake release.
6 Photocells
7
Security band
8 transmitter
Fig.20
For more information access our catalog, in the section of security and
accessories.
http://www.automatismospujol.es/arxiusdb/cataleg/cataleg.pdf
REGULATION OF THE OPENING LIMIT-SWITCH (Fig. 16)
Fix the door to the pulley with the supplied pulley fixing ring, fan-type lock washer and M10x25
countersunk bolt. If the pulley of the door and the pulley of the motor are not the same size, apply
the 220 mm adaptor. Move manually the opening stop collar (B) up to the regulation of the opening
of the door. [Fig.12). Check the travel and adjust it if necessary.
REPLACEMENT OF THE ELECTRIC WIRE
For a correct replacement of the electric wire respect the following indications:
Cut out the electric connection.Take out the lid that covers the micro switch removing the 2 screws.
Unscrew the 3 wires and the ground. Remove the stuffing box and take out the cable (if does not
slide cut it).Loosen all the wire fixings to the electronic board.
Unwire the cable from the board.
Substitute the wire for another cable with standard (4x1HO5 VVF) in case of bi-motor (4x1.5 HO5
VVF).
Wire the new cable doing the same operations in the inverse sense.
Switch on the motor and check its correct direction. If not, change the black wire and the brown
one. Make reference to the connection board indicated in the assembling instructions paying
attention to the position of the common motor (N).
GUARANTEE
The Company guarantees all products against any production fault for a period of 2 years following
the supply date.
LIABILITIES
The Company is obliged to undertake repairs of the equipments under guarantee, following
revision by the technical department.
All the equipments that, due to emergency, are delivered before the decision they are actually
under guarantee, will be considered as a standard order to be paid. Faulty equipment replaced
under guarantee will remain of property of the Company. The replacement of such equipments will
be on the installer's account and charge.
CANCELLATION
The equipment will not be under guarantee in the following cases:
- incorrect choice of the equipment given the door's characteristics
- the mounting and connecting instructions have not been followed
- payment has not been settled
English
MAX. HEIGHT
BLIND 10 mm.
ºC ºC uF
206
-20 +50 14 7,7 8,4
-20 +50 14 7,7 8,4
-20 +50 18 7,7 8,4
-20 +50 18 7,7 8,4
-20 +50 20 7,7 8,4
-20 +50 20 7,7 8,4
-20 +50 20 7,7 8,4
-20 +50 20 7,7 8,4
PULEY
220
8,9
8,9
8,9
8,9
<70dB(A)
8,9
8,9
8,9
8,9
1
2
3
4
5
6
7
8
6