Warnings Regarding Installation; Guarantee Provisions; Technical Data - Niko 350-20070 Mode D'emploi

350-20070
and the preset switch-off delay + 2 hours has not yet elapsed. After that, the lighting will be switched off,
the detector will return to the selected settings and the lighting will be switched on.
The red indication LED on the detector flashes (0.25 s on and 5 s off) to indicate that you have pressed and held
the push button. The 'long push' function can be interrupted at any time by briefly pressing the push button, after
which the lighting will be switched on and the detector will return to the selected settings.
Example 2: office
DIP switch 1 DIP switch 3
ON x
OFF x
How the absence detector works:
- The lighting must be switched on by briefly pressing the push button (daylight-independent).
- The 'eco off' and 'long push' functions are deactivated.
- The lighting is automatically switched off again after a preset time (switch-off delay), provided that no
more motion is detected by the detector in the detection area or the light level has been higher than the preset
lux value for five minutes.
Example 3: staircase
DIP switch 1 DIP switch 3
ON x x
OFF
How the presence detector works:
- The lighting is automatically switched on when the detector detects motion in the detection area and the
light level is less than the preset lux value.
- The lighting is automatically switched off again after a preset time (switch-off delay), provided that no
more motion is detected by the detector in the detection area or the light level has been higher than the preset
lux value for five minutes.
- The lighting can be switched on manually at any time via the push button, irrespective of the daylight level.
6. MAINTENANCE
Dirt may prevent the detector from functioning properly. Therefore, always keep the lens clean and dry. Use a
damp cloth and water with some detergent to clean the lens. Never exert pressure to wipe the lens clean. If
the lens or other parts of the detector are defective, please contact an authorised installer.

7. TECHNICAL DATA

dimensions
power supply voltage
power consumption
relay contact
maximum load
maximum switching capacity
maximum inrush current
light sensitivity
hysteresis on light sensitivity
switch-off delay
mounting height (fig. 3)
detection angle (fig. 3)
detection range (fig. 3)
wire input
protection degree
protection class
ambient temperature
quality mark
12
accessories
EN nv Niko sa
DIP switch 4
x
DIP switch 4
x
46.4 x 100 mm (HxB)
73.4 x 100 mm (HxW) (including non-visible part)
230 Vac ± 10%, 50 Hz
0.2 W
NO (max. 10 A), potential-free,
light- and motion-sensitive
incandescent lamps (2300 W)
230 V halogen lamps (2300 W)
all low-voltage halogen lamps (500 VA)
fluorescent lamps (non-compensated) (1200 VA)
economy lamps (CFLi) (1200 VA)
140 μF
165 A/20 ms
20 – 1000 lux
+ 10%
2 – 60 min
2 – 3.4 m
360°
circular, 3 – 20 m
3 x 2.5 mm²
IP54
class I devices
-5 – +50°C
CE marked in compliance with EN 60669-2-1
IR remote control (350-20089)
presence or absence detector 360° (slave) (350-20071)
flush-mounting box with spring terminals (350-20057)
Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu

8. WARNINGS REGARDING INSTALLATION

- The installation should be carried out by a registered installer and in compliance with the statutory regulations.
- This user manual should be presented to the user. It should be included in the electrical installation file, and
it should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko
support service.
- During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope of
each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EC declaration of conformity regarding this product at www.niko.eu.
9. NIkO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.

10. GUARANTEE PROVISIONS

- The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of purchase
of the product by the consumer. If there is no invoice, the date of production applies.
- The consumer is obliged to inform Niko in writing about the non-conformity, within two months after stating
the defect.
- In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge,
which shall be decided by Niko.
- Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
- The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
PM350-20070R13355