General Maintenance - Ego Power+ BA1120E Mode D'emploi

OPERATION
EN
POWER INDICATOR ON BATTERY PACK
This lithium-ion battery pack is equipped with a power
indicator, which indicates the charge capacity level of
the battery pack. Press the power indicator to display the
charge level. The LED indicator will shine for 10 seconds.
◾
The green light indicates that the battery pack is over
15% of its charge capacity.
◾
The red light indicates low voltage of the battery pack.
◾
The blinking red light indicates that the battery pack is
nearly depleted and needs to be charged immediately.
BATTERY PROTECTION
The battery circuitry protects the battery pack from extreme
temperature, over-discharge, and over-charge. To protect
the battery from damage and prolong its life, the battery
pack circuitry will turn off the battery pack if it becomes
overloaded or if the temperature becomes too high during
use. This may happen in extremely high torque, binding,
and stalling situations. The battery pack will shut down with
power indicator flashing orange for 10s when its operating
temperature exceeds 70°C, and will begin normal operation
when it returns to 67°C.
Notice: A significantly reduced run time after fully charging
the battery pack indicates that the batteries are near the end
of their usable life and must be replaced.
COLD WEATHER OPERATION
This Lithium-Ion battery pack will provide optimal
performance in temperatures between 5°C and 40°C.
When the battery pack is very cold, it may "pulse" for the
first minute of use to warm itself. Put the battery pack on
a tool and use the tool in a light application. After about a
minute, the battery pack will have warmed itself and will
operate normally.
WHEN TO CHARGE THE BATTERY PACK
NOTICE:
Lithium-Ion battery packs are shipped partially
charged. Before using it the first time, fully charge the
battery pack.
NOTICE:
This battery pack is equipped with an advanced
self-maintenance function to extend the battery life.
Depending on the battery charge, it will automatically
perform a self-discharge operation after one month of
storage. After this self-maintenance, the battery pack will
enter sleep mode and maintain 30% of its charge capacity.
If stored for a month or longer, fully recharge the battery
before the next use.
6
56 VOLT BATTERY — BA1120E/BA1400/BA2240E/BA2800/BA3360/BA4200
It is not necessary to run down the battery pack charge
before recharging. The Lithium-Ion battery can be charged
at any time and will not develop a "memory" when
charged after only a partial discharge. Use the power
indicator to determine when the battery pack needs to be
recharged.
HOW TO CHARGE THE BATTERY PACK
Follow the instructions in the Operator's Manual for the
EGO CH5500E Rapid Charger or CH2100E Charger.
TO ATTACH AND DETACH THE BATTERY PACK
Follow the instructions in the Operator's Manual for the
individual EGO product.
MAINTENANCE
WARNING:
To avoid serious personal injury,
always remove the battery pack from the tool when
changing accessories, cleaning or performing any
maintenance.
WARNING:
When servicing, use only identical EGO
replacement parts. Use of any other parts may create a
hazard or cause product damage.
WARNING:
It is not recommended to use compressed
dry air as a cleaning method for the battery pack. If
cleaning with compressed air is the only method to apply,
always wear safety goggles or safety glasses with side
shields. If the operation is dusty, also wear a dust mask.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean clothes to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils, etc.
come in contact with plastic parts. Chemicals can damage,
weaken or destroy plastic which may result in serious
personal injury.
WARNING:
TO REDUCE THE RISK OF FIRE, PERSONAL
INJURY, AND PRODUCT DAMAGE DUE TO A SHORT
CIRCUIT, NEVER IMMERSE YOUR TOOL, BATTERY PACK
OR CHARGER IN FLUID OR ALLOW A FLUID TO FLOW
INSIDE THEM. CORROSIVE OR CONDUCTIVE FLUIDS, SUCH
AS SEAWATER, CERTAIN INDUSTRIAL CHEMICALS, AND
BLEACH OR BLEACH CONTAINING PRODUCTS, ETC., CAN
CAUSE A SHORT CIRCUIT.