Noise/Vibration Information - Bosch GSH 11 E PROFESSIONAL Instructions D'emploi

OBJ_BUCH-1 619 929 697-003.book Page 3 Tuesday, February 14, 2006 3:05 PM
Technical Data
Demolition Hammer
Article number
Rated power input
Impact rate
Impact energy per stroke
Chisel positions
Chiselling capacity in
concrete of medium
hardness
Tool holder
Lubrication
Weight according to
EPTA-Procedure
01/2003
Protection class
The values given are valid for nominal voltages [U] of
230/240 V. For lower voltage and models for specific coun-
tries, these values can vary.
Please observe the article number on the type plate of your
machine. The trade names of the individual machines may
vary.
Product Features
The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Dust protection cap
2 Locking sleeve
3 Chisel adjustment ring (Vario-lock)
4 On/Off switch
5 Thumbwheel for preselection of impact rate
6 Service indicator
7 Auxiliary handle
8 Knurled nut for auxiliary handle
Not all of the accessories illustrated or described are
included as standard delivery.

Noise/Vibration Information

Measured values determined according to EN 60745.
Typically the A-weighted noise level of the machine is:
sound pressure level 89 dB(A); sound power level
100 dB(A). Uncertainty K=3 dB.
Wear hearing protection!
Overall vibrational values (vector sum of three direc-
tions) determined according to EN 60745:
Chiselling: Vibration emission value a
2
uncertainty K=2 m/s .
1 619 929 697 • 14.2.06
GSH 11 E
PROFESSIONAL
0 611 316 7..
W 1500
bpm 900–1890
J 6–25
12
kg/h 490
SDS-max
Central permanent
lubrication
kg 10.1
/II
2
=16 m/s ,
h
English–3
The vibration emission level given in
WARNING
this information sheet has been meas-
ured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another.
The vibration emission level will vary because of the
ways in which a power tool can be used and may
increase above the level given in this information sheet.
This could lead to a significant underestimate of expo-
sure when the tool is used regularly in such a way.
Note: To be accurate, an estimation of the level of
exposure to vibration experienced during a given period
of work should also take into account the times when
the tool is switched off and when it is running but not
actually doing the job. This may significantly reduce the
exposure level over the total working period.
Declaration of Conformity
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents: EN 60745 according to
the provisions of the directives 89/336/EWG,
98/37/EG, 2000/14/EG.
2000/14/EG: The guaranteed sound power level L
is below 105 dB(A). The valuation procedure for the
conformity is in accordance with appendix VI.
Designated testing authority:
TÜV NORD CERT GmbH & Co. KG,
Am TÜV 1, 30519 Hannover
Leinfelden, 01.12.2005
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
Robert Bosch GmbH, Power Tools Division
Assembly
Auxiliary Handle
Operate your machine only with the auxiliary
handle 7.
The auxiliary handle 7 can be set to any position for a
secure and low-fatigue working posture.
Loosen the knurled nut 8, rotate the auxiliary handle 7
around the axis of the machine to the required position
and tighten the knurled nut 8 again.
WA